Yamaha PW50W 2007 Скачать руководство пользователя страница 158

Страница: 158 / 168

ELEC

7-8

IGNITION SYSTEM

8. Ignition control switch

Check the ignition control switch for conti-
nuity. Refer to “CHECKING THE SWITCH-
ES”.

Is the ignition control switch OK?

YES

Replace the ignition
control switch.

7. Lighting coil resistance

Disconnect the lighting coil coupler from
the wire harness.

Connect the pocket tester (“Ω

1” range) to

the lighting coil terminal as shown.

Positive tester probe

→

white

Negative tester probe

→

black

Measure the charge coil resistance.

Is the lighting coil OK?

B W

W/R B/R

Lighting coil resistance

0.57–0.69

Ω

at 20°C (68°F)

(between white and black)

YES

Replace the stator
coil assembly.

W/R B/R

B/Y

W/B

YES

Replace the control
unit assembly.

Control unit resistance

9. Control unit resistance

Disconnect the control unit

coupler

from the wire harness.

Connect the pocket tester (“Ω

1k” range)

to the control unit terminal as shown.

Positive tester probe

Negative tester probe

Measure the control unit resistance.

Is the control unit OK?

Tester negative lead

Range

B/R W/R W/B B/Y

B/R

100 — 80 — 80 — 80 —

200 kΩ 200 kΩ 200 kΩ 200 kΩ

W/R

∞

∞ ∞ ∞

W/B 80 — 30 —

10 — 1 —

1 kΩ

200 kΩ 50 kΩ

20 kΩ 5 kΩ

B/Y 80 — 30 — 10 —

10 —

200 kΩ 80 kΩ 20 kΩ

20 kΩ

80 — 20 — 1 —

7 —

200 kΩ 50 kΩ 5 kΩ 15 kΩ

Tester
positive
lead

5PG-7-10 156

06.5.16, 17:45:15

Содержание PW50W 2007









































































































































































Результаты поиска

Содержание PW50W 2007

Отзывы:

Похожие инструкции для PW50W 2007

Бренды по названию

Популярные бренды

Yamaha PW50W 2007, Руководство по обслуживанию

Результаты поиска

Содержание PW50W 2007

Отзывы:

Похожие инструкции для PW50W 2007

Бренды по названию

Популярные бренды