manualshive.com logo in svg

Yamaha MTN850-A 2017, Руководство по обслуживанию

Поделиться
Скачать
Yamaha MTN850-A 2017 Скачать руководство пользователя страница 75

CABLE ROUTING

2-38

1. Throttle cable
2. Meter
3. Stay 1
4. Brake hose
5. Bracket 1
6. Wire harness
7. Horn
8. Master cylinder
9. Meter lead
10.Headlight lead
11.Meter bracket
12.Headlight coupler

A. To headlight
B.  Clamp the left and right leads of the handle-

bar switch to the rounded part of the handle-

bar.

Route the left and right leads from the han-

dlebar switches under and along the handle-

bar.

Make sure that the clamp closure faces to the 

front and the clamp end points down.

C.  Insert the clamp of the wire harness into the 

hole in the stay 1.

D.  The L-type terminal of the horn should face to 

the outside of the vehicle.

E.  Insert the clamp of the wire harness into the 

hole in the bracket.

F.  Install along the side of the master cylinder. 

Point the claws downward and make sure the 

damper faces toward the master cylinder and 

clamp.

G. Route the throttle cable and front brake hose 

between the handle crown and the bracket 1.

H.  Route the meter lead between the meter 

bracket and the headlight stay.

I. To 

meter

J.  Hook the headlight lead in the claw of the 

headlight.

K.  Route the headlight lead between the meter 

bracket and the headlight stay.

L.  Insert the clamp into the long hole.

Check that either the upper or lower claw has 

been hooked.

Содержание MTN850-A 2017

















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды