manualshive.com logo in svg

Yamaha MTN850-A 2017, Руководство по обслуживанию

Поделиться
Скачать
Yamaha MTN850-A 2017 Скачать руководство пользователя страница 121

PERIODIC MAINTENANCE

3-11

•

Fuel tank cover
Refer to “GENERAL CHASSIS (1)” on page
4-1.

•

Rider seat
Refer to “GENERAL CHASSIS (1)” on page
4-1.

•

Air scoop
Refer to “GENERAL CHASSIS (1)” on page
4-1.

EAS30799

ADJUSTING THE EXHAUST GAS VOLUME

TIP

•

Be sure to set the CO density level to standard,
and then adjust the exhaust gas volume.

•

To adjust the exhaust gas volume, use the CO
adjustment mode of the Yamaha diagnostic
tool. For more information, refer to the opera-
tion manual of the Yamaha diagnostic tool.

1. Connect the Yamaha diagnostic tool to the

coupler. For information about connecting the
Yamaha diagnostic tool, refer to “YAMAHA
DIAGNOSTIC TOOL” on page 8-36.

EAS30627

CHECKING THE AIR INDUCTION SYSTEM

Refer to “CHECKING THE AIR INDUCTION
SYSTEM” on page 7-19.

EAS30623

CHECKING THE CYLINDER HEAD 

BREATHER HOSE

1. Remove:

•

Air filter case
Refer to “GENERAL CHASSIS (2)” on page
4-7.

2. Check:

•

Cylinder head breather hose “1”
Cracks/damage 

 Replace.

Loose connection 

 Connect properly.

NOTICE

ECA14920

Make sure the cylinder head breather hose is

routed correctly.

3. Install:

•

Air filter case
Refer to “GENERAL CHASSIS (2)” on page
4-7.

EAS30628

REPLACING THE AIR FILTER ELEMENT

1. Remove:

•

Air scoop
Refer to “GENERAL CHASSIS (1)” on page
4-1.

•

Rider seat
Refer to “GENERAL CHASSIS (1)” on page
4-1.

•

Fuel tank cover
Refer to “GENERAL CHASSIS (1)” on page
4-1.

•

Fuel tank
Refer to “FUEL TANK” on page 7-1.

2. Remove:

•

ECU (Engine Control Unit) “1”

•

Air filter case cover “2”
Refer to “GENERAL CHASSIS (2)” on page
4-7.

3. Check:

•

Air filter element “1”

•

Air filter seal
Damage 

 Replace.

TIP

•

Replace the air filter element every 40000 km
(24000 mi) of operation.

•

The air filter needs more frequent service if you
are riding in unusually wet or dusty areas.

Yamaha diagnostic tool USB

90890-03250

Yamaha diagnostic tool (A/I)

90890-03252

a

1

a

a

2

1

Содержание MTN850-A 2017

















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды