manualshive.com logo in svg

Yamaha MTN850-A 2017, Руководство по обслуживанию

Поделиться
Скачать
Yamaha MTN850-A 2017 Скачать руководство пользователя страница 282

CLUTCH

5-47

•

Clutch springs

•

Pressure plate 1

•

Clutch spring bolts “1”

•

Oil pump driven sprocket “2”

TIP

•

Tighten the clutch spring bolts in stages and in
a crisscross pattern.

•

Apply lithium-soap-based grease onto the pull
rod.

•

Position the pull rod so that the teeth “a” face
towards the hole “b”. Then, install the clutch
cover.

5. Install:

•

Dowel pins

•

Clutch cover gasket 

•

Clutch cover

•

Cover

TIP

•

Apply engine oil onto the bearing.

•

Tighten the clutch cover bolts in stages and in

a crisscross pattern.

6. Install:

•

Pull lever

TIP

•

Install the pull lever with the “O” mark facing to-
ward lower side.

•

When installing the pull lever, push the pull le-
ver and check that the punch mark “a” on the
pull lever aligns with the mark “b” on the clutch
cover. Make sure that the pull rod teeth and
pull lever shaft pinion gear are engaged.

7. Connect:

•

Clutch cable “1”

TIP

•

For the clutch cable “1”, turn the nut “2” in fully
and then adjust the length “a” by using the nut
“3” so that the cable length is 47.1–54.8 mm
(1.85–2.16 in).

•

Measure the length while keeping the measur-
ing surface “b” parallel.

•

After installing the clutch cable, bend the pro-
jection “c” on the pull lever.

Clutch spring bolt

10 N·m (1.0 kgf·m, 7.2 lb·ft)

Oil pump driven sprocket bolt

15 N·m (1.5 kgf·m, 11 lb·ft)

LOCTITE®

Clutch cover bolt

12 N·m (1.2 kgf·m, 8.7 lb·ft)

T

R

.

.

T

R

.

.

1

1

a

b

2

New

T

R

.

.

a

b

Содержание MTN850-A 2017

















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды