manualshive.com logo in svg

Yamaha MTN850-A 2017, Руководство по обслуживанию

Поделиться
Скачать
Yamaha MTN850-A 2017 Скачать руководство пользователя страница 129

PERIODIC MAINTENANCE

3-19

2. Adjust:

•

Drive chain slack

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Loosen both locknuts “1”.
b. Turn both adjusting bolts “2” in direction “a” or

“b” until the specified drive chain slack is ob-
tained.

TIP

•

To maintain the proper wheel alignment, adjust
both sides evenly.

•

There should be no clearance between the ad-
justing block and adjusting bolt.

c. Tighten the wheel axle nut to specification.

d. Tighten the locknuts to specification.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS30803

LUBRICATING THE DRIVE CHAIN

The drive chain consists of many interacting
parts. If the drive chain is not maintained proper-
ly, it will wear out quickly. Therefore, the drive
chain should be serviced, especially when the
vehicle is used in dusty areas.
This vehicle has a drive chain with small rubber
O-rings between each side plate. Steam clean-
ing, high-pressure washing, certain solvents,
and the use of a coarse brush can damage
these O-rings. Therefore, use only kerosene to
clean the drive chain. Wipe the drive chain dry

and thoroughly lubricate it with engine oil or
chain lubricant that is suitable for O-ring chains.
Do not use any other lubricants on the drive
chain since they may contain solvents that could
damage the O-rings.

EAS30645

CHECKING AND ADJUSTING THE 

STEERING HEAD

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is

no danger of it falling over.

TIP

Place the vehicle on a maintenance stand so
that the front wheel is elevated.

2. Check:

•

Steering head
Grasp the bottom of the front fork legs and
gently rock the front fork.
Blinding/looseness 

 Adjust the steering

head. 

3. Remove:

•

Upper bracket

4. Adjust:

•

Steering head

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Remove the lock washer “1”, the upper ring

nut “2”, and the rubber washer “3”.

b. Loosen the lower ring nut “4” and then tighten

it to specification with a steering nut wrench
“5”.

TIP

•

Set the torque wrench at a right angle to the
steering nut wrench.

•

Move the steering to the left and right a couple
of times to check that it moves smoothly.

Direction “a”

Drive chain is tightened.

Direction “b”

Drive chain is loosened.

Rear wheel axle nut

150 N·m (15 kgf·m, 108 lb·ft)

Chain puller adjusting bolt lock-

nut

16 N·m (1.6 kgf·m, 12 lb·ft)

1

2

a

b

T

R

.

.

T

R

.

.

Recommended lubricant

Chain lubricant suitable for O-

ring chains

Содержание MTN850-A 2017

















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды