Yamaha MTN850-A 2017 Скачать руководство пользователя страница 127

Страница: 127 / 560

PERIODIC MAINTENANCE

3-17

WARNING

EWA13181

• The tire pressure should only be checked

and regulated when the tire temperature

equals the ambient air temperature.

• The tire pressure and the suspension must

be adjusted according to the total weight

(including cargo, rider, passenger and ac-

cessories) and the anticipated riding

speed.

• Operation of an overloaded vehicle could

cause tire damage, an accident or an injury.

NEVER OVERLOAD THE VEHICLE.

2. Check:

•

Tire surfaces
Damage/wear



Replace the tire.

WARNING

EWA13190

It is dangerous to ride with a worn-out tire.

When the tire tread reaches the wear limit, re-

place the tire immediately.

WARNING

EWA14090

After extensive tests, the tires listed below

have been approved by Yamaha Motor Co.,

Ltd. for this model. The front and rear tires

should always be by the same manufacturer

and of the same design. No guarantee con-

cerning handling characteristics can be giv-

en if a tire combination other than one

approved by Yamaha is used on this vehicle.

WARNING

EWA13210

New tires have a relatively low grip on the

road surface until they have been slightly

worn. Therefore, approximately 100 km

should be traveled at normal speed before

any high-speed riding is done.

TIP

For tires with a direction of rotation mark “1”:

•

Install the tire with the mark pointing in the di-
rection of wheel rotation.

•

Align the mark “2” with the valve installation
point.

Tire air pressure (measured on

cold tires)

1 person

Front

250 kPa (2.50 kgf/cm², 36 psi)

Rear

290 kPa (2.90 kgf/cm², 42 psi)

2 persons

Front

250 kPa (2.50 kgf/cm², 36 psi)

Rear

290 kPa (2.90 kgf/cm², 42 psi)

Maximum load

174 kg (384 lb)

* Total weight of rider, passenger, cargo

and accessories

1. Tire tread depth
2. Side wall
3. Wear indicator

Wear limit (front)

1.5 mm (0.06 in) (AUS)

1.6 mm (0.06 in) (EUR)(RUS)

Wear limit (rear)

1.5 mm (0.06 in) (AUS)

1.6 mm (0.06 in) (EUR)(RUS)

Front tire

Size

120/70 ZR17 M/C (58W)

Manufacturer/model

BRIDGESTONE/S20F

Manufacturer/model

DUNLOP/D214F

Rear tire

Size

180/55 ZR17M/C (73W)

Manufacturer/model

BRIDGESTONE/S20R

Manufacturer/model

DUNLOP/D214

Содержание MTN850-A 2017

















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MTN850-A 2017

Отзывы:

Бренды по названию

Популярные бренды

Yamaha MTN850-A 2017, Руководство по обслуживанию

Результаты поиска

Содержание MTN850-A 2017

Отзывы:

Бренды по названию

Популярные бренды