manualshive.com logo in svg

Yamaha MTN850-A 2017, Руководство по обслуживанию

Поделиться
Скачать
Yamaha MTN850-A 2017 Скачать руководство пользователя страница 345

THROTTLE BODIES

7-12

e. Start the engine.
f. Measure the fuel line pressure.

Faulty 

 Replace the fuel pump.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS31159

INSTALLING THE FUEL HOSE (FUEL RAIL 

SIDE)

1. Connect:

•

Fuel hose (fuel rail side)

NOTICE

ECA17500

When installing the fuel hose, make sure that

it is securely connected, and that the fuel

hose connector cover on the fuel hose is in

the correct position, otherwise the fuel hose

will not be properly installed.

TIP

•

Install the fuel hose securely onto the fuel rail
joint until a distinct “click” is heard.

•

To install the fuel hose onto the fuel rail joint,
slide the fuel hose connector cover “1” on the
end of the hose in the direction of the arrow
shown.

•

It is prohibited to wear the cotton work gloves
or equivalent coverings.

EAS30485

ADJUSTING THE THROTTLE POSITION 

SENSOR

NOTICE

ECA17540

• Handle the throttle position sensor with

special care.

• Never subject the throttle position sensor

to strong shocks. If the throttle position

sensor is dropped, replace it.

1. Check:

•

Throttle position sensor
Refer to “CHECKING THE THROTTLE PO-
SITION SENSOR” on page 8-170.

2. Adjust:

•

Throttle position sensor angle

TIP

Before adjusting the throttle position sensor, the
throttle bodies must be removed.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Temporary tighten the throttle position sensor

screws.

b. Check that the throttle valves are fully closed.
c. Connect the throttle position sensor to the

wire harness.

d. Remove the protective cap “1”, and then con-

nect the Yamaha diagnostic tool to coupler.

TIP

For information about using the Yamaha diag-
nostic tool, refer to the operation manual that is
included with the tool.

e. Diagnostic code number “01” is selected.
f. Adjust the position of the throttle position sen-

sor angle so that 11–21 can appear in the
Yamaha diagnostic tool screen.

g. After adjusting the throttle position sensor an-

gle, tighten the throttle position sensor
screws “2”.

Fuel line pressure (at idle)

300–390 kPa (3.0–3.9 kgf/cm², 

43.5–56.6 psi)

2

3

Throttle position sensor screw

3.5 N·m (0.35 kgf·m, 2.5 lb·ft)

1

T

R

.

.

Содержание MTN850-A 2017

















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды