Yamaha MTN850-A 2017 Скачать руководство пользователя страница 157

Страница: 157 / 560

FRONT WHEEL

4-12

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

2. Install:

•

Front wheel sensor rotor

NOTICE

ECA17200

Replace the wheel sensor rotor bolts with

new ones.

TIP

Install the wheel sensor rotor with the stamped
mark “1” facing outward.

3. Measure:

•

Wheel sensor rotor runout
Out of specification



Correct the wheel sen-

sor rotor runout or replace the wheel sensor
rotor.
Refer to “MAINTENANCE OF THE FRONT
WHEEL SENSOR AND SENSOR ROTOR”
on page 4-12.

EAS31151

MAINTENANCE OF THE FRONT WHEEL

SENSOR AND SENSOR ROTOR

NOTICE

ECA21070

• Handle the ABS components with care

since they have been accurately adjusted.

Keep them away from dirt and do not sub-

ject them to shocks.

• The front wheel sensor cannot be disas-

sembled. Do not attempt to disassemble it.

If faulty, replace with a new one.

• Keep any type of magnets (including mag-

netic pick-up tools, magnetic screwdrivers,

etc.) away from the front wheel sensor or

front wheel sensor rotor.

• Do not drop or shock the wheel sensor or

the wheel sensor rotor.

1. Check:

•

Front wheel sensor “1”
Cracks/bends/distortion



Replace.

Iron powder/dust



Clean.

2. Check:

•

Front wheel sensor rotor “1”
Cracks/damage/scratches



Replace the

front wheel sensor rotor.
Iron powder/dust/solvent



Clean.

TIP

•

The wheel sensor rotor is installed on the inner
side of the wheel hub.

•

When cleaning the wheel sensor rotor, be
careful not to damage the surface of the sensor
rotor.

3. Measure:

•

Wheel sensor rotor runout
Out of specification



Clean the installation

surface of the wheel sensor rotor and correct
the wheel sensor rotor runout, or replace the
wheel sensor rotor.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Hold the dial gauge at a right angle against

the wheel sensor rotor surface.

b. Measure the wheel sensor rotor runout.

Wheel sensor rotor bolt

8 N·m (0.8 kgf·m, 5.8 lb·ft)

LOCTITE®

Wheel sensor rotor runout limit

0.25 mm (0.01 in)

Wheel sensor rotor runout limit

0.25 mm (0.01 in)

Содержание MTN850-A 2017

















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MTN850-A 2017

Отзывы:

Бренды по названию

Популярные бренды

Yamaha MTN850-A 2017, Руководство по обслуживанию

Результаты поиска

Содержание MTN850-A 2017

Отзывы:

Бренды по названию

Популярные бренды