manualshive.com logo in svg

Yamaha MTN850-A 2017, Руководство по обслуживанию

Поделиться
Скачать
Yamaha MTN850-A 2017 Скачать руководство пользователя страница 188

REAR BRAKE

4-43

EAS30183

INTRODUCTION

WARNING

EWA14101

Disc brake components rarely require disas-

sembly. Therefore, always follow these pre-

ventive measures:

• Never disassemble brake components un-

less absolutely necessary.

• If any connection on the hydraulic brake

system is disconnected, the entire brake

system must be disassembled, drained,

cleaned, properly filled, and bled after reas-

sembly.

• Never use solvents on internal brake com-

ponents.

• Use only clean or new brake fluid for clean-

ing brake components.

• Brake fluid may damage painted surfaces

and plastic parts. Therefore, always clean

up any spilt brake fluid immediately.

• Avoid brake fluid coming into contact with

the eyes as it can cause serious injury.

FIRST AID FOR BRAKE FLUID ENTERING

THE EYES:

• Flush with water for 15 minutes and get im-

mediate medical attention.

EAS30184

CHECKING THE REAR BRAKE DISC

1. Remove:

•

Rear wheel
Refer to “REAR WHEEL” on page 4-16.

2. Check:

•

Rear brake disc
Damage/galling 

 Replace.

3. Measure:

•

Brake disc runout
Out of specification 

 Correct the brake disc

runout or replace the brake disc.
Refer to “CHECKING THE FRONT BRAKE
DISCS” on page 4-30.

4. Measure:

•

Brake disc thickness
Measure the brake disc thickness at a few dif-
ferent locations.
Out of specification 

 Replace.

Refer to “CHECKING THE FRONT BRAKE
DISCS” on page 4-30.

5. Adjust:

•

Brake disc runout
Refer to “CHECKING THE FRONT BRAKE
DISCS” on page 4-30.

6. Install:

•

Rear wheel
Refer to “REAR WHEEL” on page 4-16.

EAS30185

REPLACING THE REAR BRAKE PADS

TIP

When replacing the brake pads, it is not neces-
sary to disconnect the brake hose or disassem-
ble the brake caliper.

1. Measure:

•

Brake pad wear limit “a”
Out of specification 

 Replace the brake

pads as a set.

2. Install:

•

Brake pad insulators

•

Brake pad shims
(onto the brake pads)

•

Brake pad spring
(into the rear brake caliper)

•

Brake pads

TIP

Always install new brake pads, brake pad insu-
lators, brake pad shims, and brake pad spring as
a set.

Brake disc runout limit (as mea-

sured on wheel)

0.15 mm (0.0059 in)

Brake disc thickness limit

4.5 mm (0.18 in)

Rear brake disc bolt

30 N·m (3.0 kgf·m, 22 lb·ft)

LOCTITE®

Brake pad lining thickness

6.0 mm (0.24 in)

Limit

1.0 mm (0.04 in)

T

R

.

.

a

Содержание MTN850-A 2017

















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды