manualshive.com logo in svg

Yamaha MTN850-A 2017, Руководство по обслуживанию

Поделиться
Скачать
Yamaha MTN850-A 2017 Скачать руководство пользователя страница 301

CONNECTING RODS AND PISTONS

5-66

necting rod cap faces the same direction as the
“Y” mark “b” on the connecting rod.

•

Make sure the “Y” marks “b” on the connecting
rods face towards the left side of the crank-
shaft.

g. Tighten the connecting rod bolts with a torque

wrench.

h. Put a mark “1” on the corner of the connecting

rod bolt “2” and the connecting rod cap “3”.

i. Tighten the connecting rod bolts further to

reach the specified angle 175

–185

.

WARNING

EWA16610

If the bolt is tightened more than the speci-

fied angle, do not loosen the bolt and then re-

tighten it. Instead, replace the bolt with a new

one and perform the procedure again.

NOTICE

ECA20890

Do not use a torque wrench to tighten the

bolt to the specified angle.

j. After the installation, check that the section

shown “a” is flush with each other by touching
the surface.

k. Remove the connecting rod and big end

bearings.

l. Measure the compressed Plastigauge®

width on the crankshaft pin. If the crankshaft-
pin-to-big-end-bearing clearance is out of
specification, select replacement big end
bearings.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

2. Select:

•

Big end bearings (P

1

–P

3

)

TIP

•

The numbers “A” stamped into the crankshaft
web and the numbers “1” on the connecting
rods are used to determine the replacement
big end bearings sizes.

•

“P

1

”–“P

3

” refer to the bearings shown in the

crankshaft illustration.

For example, if the connecting rod “P

1

” and

the crankshaft web “P

1

” numbers are 5 and 2

respectively, then the bearing size for “P

1

” is:

Connecting rod bolt (1st)

20 N·m (2.0 kgf·m, 14 lb·ft)

Connecting rod bolt (final)

Specified angle 175

–185

a

b

T

R

.

.

T

R

.

.

180˚

“P

1

” (connecting rod) - “P

1

” (crankshaft) = 5 - 2 = 

3 (brown)

a

Содержание MTN850-A 2017

















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды