manualshive.com logo in svg

Yamaha MTN850-A 2017, Руководство по обслуживанию

Поделиться
Скачать
Yamaha MTN850-A 2017 Скачать руководство пользователя страница 22

IMPORTANT INFORMATION

1-13

EAS20009

IMPORTANT INFORMATION

EAS30006

PREPARATION FOR REMOVAL AND 

DISASSEMBLY

1. Before removal and disassembly, remove all

dirt, mud, dust and foreign material.

2. Use only the proper tools and cleaning equip-

ment.
Refer to “SPECIAL TOOLS” on page 1-20.

3. When disassembling, always keep mated

parts together. This includes gears, cylinders,
pistons and other parts that have been “mat-
ed” through normal wear. Mated parts must
always be reused or replaced as an assem-
bly.

4. During disassembly, clean all of the parts and

place them in trays in the order of disassem-
bly. This will speed up assembly and allow for
the correct installation of all parts.

5. Keep all parts away from any source of fire.

EAS30007

REPLACEMENT PARTS

Use only genuine Yamaha parts for all replace-
ments. Use oil and grease recommended by
Yamaha for all lubrication jobs. Other brands
may be similar in function and appearance, but
inferior in quality.

EAS30008

GASKETS, OIL SEALS AND O-RINGS

1. When overhauling the engine, replace all

gaskets, seals and O-rings. All gasket surfac-
es, oil seal lips and O-rings must be cleaned.

2. During reassembly, properly oil all mating

parts and bearings and lubricate the oil seal
lips with grease.

EAS30009

LOCK WASHERS/PLATES AND COTTER 

PINS

After removal, replace all lock washers/plates
“1” and cotter pins. After the bolt or nut has been
tightened to specification, bend the lock tabs
along a flat of the bolt or nut.

EAS30010

BEARINGS AND OIL SEALS

Install bearings “1” and oil seals “2” so that the
manufacturer marks or numbers are visible.

1. Oil
2. Lip
3. Spring
4. Grease

Содержание MTN850-A 2017

















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды