manualshive.com logo in svg

Yamaha MTN850-A 2017, Руководство по обслуживанию

Поделиться
Скачать
Yamaha MTN850-A 2017 Скачать руководство пользователя страница 130

PERIODIC MAINTENANCE

3-20

c. Loosen the lower ring nut “6” completely,

then tighten it to specification.

WARNING

EWA13140

Do not overtighten the lower ring nut.

d. Check the steering head for looseness or

binding by turning the front fork all the way in
both directions. If any binding is felt, remove
the lower bracket and check the upper and
lower bearings.
Refer to “STEERING HEAD” on page 4-71.

e. Install the rubber washer “7”.
f. Install the upper ring nut “8”.
g. Finger tighten the upper ring nut, then align

the slots of both ring nuts. If necessary, hold
the lower ring nut and tighten the upper ring
nut until their slots are aligned.

h. Install the lock washer “9”.

TIP

Make sure the lock washer tabs “a” sit correctly
in the ring nut slots “b”.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

5. Install:

•

Upper bracket
Refer to “HANDLEBAR” on page 4-58.

EAS30646

LUBRICATING THE STEERING HEAD

1. Lubricate:

•

Upper bearing

•

Lower bearing

•

Bearing race

EAS31186

CHECKING THE CHASSIS FASTENERS

Make sure that all nuts, bolts, and screws are
properly tightened.
Refer to “CHASSIS TIGHTENING TORQUES”
on page 2-13.

EAS30804

LUBRICATING THE BRAKE LEVER

Lubricate the pivoting point and metal-to-metal
moving parts of the lever.

EAS30805

LUBRICATING THE CLUTCH LEVER

Lubricate the pivoting point and metal-to-metal
moving parts of the lever.

EAS30649

LUBRICATING THE PEDAL

Lubricate the pivoting point and metal-to-metal
moving parts of the pedal.

Steering nut wrench

90890-01403

Exhaust flange nut wrench

YU-A9472

Lower ring nut (initial tightening 

torque)

52 N·m (5.2 kgf·m, 38 lb·ft)

Lower ring nut (final tightening 

torque)

18 N·m (1.8 kgf·m, 13 lb·ft)

T

R

.

.

T

R

.

.

Recommended lubricant

Lithium-soap-based grease

Recommended lubricant

Silicone grease

Recommended lubricant

Lithium-soap-based grease

Recommended lubricant

Lithium-soap-based grease

Содержание MTN850-A 2017

















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды