Yamaha LZ250B Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 126

background image

E

3-2

EMU01478

MOUNTING THE OUTBOARD MOTOR

w

8

Overpowering  a  boat  may  cause
severe instability. Do not install an out-
board  motor  with  more  horsepower
than  the  maximum  rating  on  the
capacity  plate  of  the  boat. If  the  boat
does not have a capacity plate, consult
the boat manufacturer.

8

The information presented in this sec-
tion is intended as reference only. It is
not possible to provide complete
instructions

for

every

possible

boat/motor

combination.

Proper

mounting depends in part on experi-
ence and the specific boat/motor com-
bination.

w

Improper  mounting  of  the  outboard
motor  could  result  in  hazardous  condi-
tions such as poor handling, loss of con-
trol, or  fire  hazards. Observe  the  follow-
ing:

8

For  permanently  mounted  models,
your  dealer  or  other  person  experi-
enced  in  proper  rigging  should  mount
the  motor. If  you  are  mounting  the
motor  yourself, you  should  be  trained
by an experienced person.

8

For  portable  models, your  dealer  or
other  person  experienced  in  proper
outboard  motor  mounting  should
show you how to mount your motor.

60V-9-11-3 7/31/02 1:52 PM Page 3

«
...
51
52
53
54
55
...
»

Содержание LZ250B































































































































Отзывы:

Нет отзывов

Похожие инструкции для LZ250B

Бренд: Abit Страницы: 120

Бренд: Yamaha Страницы: 86

Бренд: MACHINIST Страницы: 15

Бренд: NXP Semiconductors Страницы: 14

Бренд: WinFast Страницы: 75

Бренд: JETWAY Страницы: 43

Бренд: Gigabyte Страницы: 81

Бренд: MINATO Страницы: 125

Бренд: Maxim Страницы: 7

Бренд: Digilent Страницы: 23

Бренд: DFI Страницы: 150

Бренд: Gigabyte Страницы: 38

Бренд: IDT Страницы: 5

Бренд: Supero Страницы: 121

Бренд: IEI Technology Страницы: 21

Бренд: DFI Страницы: 76

Бренд: spacewalker Страницы: 34

Бренд: ASROCK Страницы: 181

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды