Yamaha LZ250B Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 126

background image

E

5-7

NOTE:

8

Reserve oil capacity is maximum 1,500
cm

3

(1.6 US qt, 1.31 Imp qt).

8

The  oil  feed  pump  will  not  operate  if  the
engine  is  tilted  more  than  35°. Put  the
engine  in  the  down  position  before  oper-
ating the emergency switch.

EMU01511

TREATMENT OF SUBMERGED
MOTOR

If  the  outboard  motor  is  submerged,  imme-
diately  take  it  a Yamaha  dealer. Otherwise,
some  corrosion  may  begin  almost  immedi-
ately.
If you cannot immediately take the outboard
motor to a Yamaha dealer, follow the proce-
dure  below  in  order  to  minimize  engine
damage.

EMU00449

1)

Thoroughly wash away mud, salt, sea-
weed, etc. with fresh water.

2)

Remove the spark plugs and face the
spark plug holes downward to allow any
water, mud or contaminants to drain.

3)

Drain the fuel from the vapor separator,
fuel filter and fuel line.

4)

Feed  fogging  oil  or  engine  oil  through
the  intake  manifold  and  spark  plug
holes  while  cranking  with  the  emer-
gency starter rope.

5)

Take the outboard motor to a Yamaha
dealer as soon as possible.

c

C

Do not attempt to run the motor until it
has been completely inspected.

107012

107013

107014

60V-9-11-5 7/31/02 10:28 AM Page 8

«
...
112
113
114
115
116
...
»

Содержание LZ250B































































































































Отзывы:

Нет отзывов

Похожие инструкции для LZ250B

PIC18F57Q43 Curiosity Nano

Бренд: Microchip Technology Страницы: 34

Бренд: Aaeon Страницы: 132

Бренд: Aaeon Страницы: 50

Бренд: JETWAY Страницы: 52

Kontron mITX-CFL-S

Бренд: S&T Страницы: 8

SuperServer SYS-E102-9AP-LN4-C

Бренд: Supermicro Страницы: 81

Бренд: ECS Страницы: 93

Бренд: Texas Instruments Страницы: 13

Бренд: Biostar Страницы: 166

Бренд: Aaeon Страницы: 119

Бренд: ASROCK Страницы: 64

Бренд: Biostar Страницы: 31

Бренд: ECS Страницы: 82

Бренд: Tadao Страницы: 3

Бренд: DFI Страницы: 44

Бренд: Supero Страницы: 82

Бренд: Silicon Laboratories Страницы: 12

Бренд: ASROCK Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды