Yamaha LZ250B Скачать руководство пользователя страница 36

Страница: 36 / 126

2-11

EMU01614

DIGITAL TACHOMETER

This gauge contains the tachometer, trim
meter, hour meter, oil level indicator, and
the overheat warning indicator.

Tachometer

Trim meter

Hour meter

Oil level indicator

Overheat warning indicator

Set button

Mode button

NOTE:

All segments of the display will light
momentarily after the main switch is turned
on and will return to normal thereafter.

EMU00136

Tachometer

This meter shows the engine speed.

EMU01689

Trim Meter

This meter shows the trim angle of your out-
board motor.

NOTE:

Memorize  the  trim  angles  that  work  best
for  your  boat  under  different  conditions.
Adjust  the  trim  angle  to  the  desired  set-
ting  by  operating  the  power  trim  and  tilt
switch.

If the trim angle of your motor exceeds
the trim operating range, the top segment
on the trim meter display will start to blink.

001078

001082

001049

001050

60V-9-11-2 7/31/02 10:26 AM Page 12

Содержание LZ250B































































































































Результаты поиска

Содержание LZ250B

Отзывы:

Похожие инструкции для LZ250B

Бренды по названию

Популярные бренды

Yamaha LZ250B, Руководство пользователя

Результаты поиска

Содержание LZ250B

Отзывы:

Похожие инструкции для LZ250B

Бренды по названию

Популярные бренды