Yamaha LZ250B Скачать руководство пользователя страница 91

Страница: 91 / 126

4-14

EMU00370

INSPECTING FUEL FILTER

Gasoline (petrol) is highly flammable,
and its vapors are flammable and explo-
sive.

If you have any question about proper-
ly doing this procedure, consult your
Yamaha dealer.

Do not perform this procedure on a hot
or running engine. Allow the engine to
cool.

There will be fuel in the fuel filter. Keep
away from sparks, cigarettes, flames
or other sources of ignition.

This procedure will allow some fuel to
spill. Catch fuel in a rag. Wipe up any
spilled fuel immediately.

The  fuel  filter  must  be  reassembled
carefully  with  O-ring, filter  cup, and
hoses  in  place. Improper  assembly  or
replacement  can  result  in  a  fuel  leak,
which  could  result  in  a  fire  or  explo-
sion hazard.

EMU01308

NOTE:

If any water is in the fuel, the float

will

rise. If so, remove the cup and drain the
water.

Loosen and remove the locking tab bolt
and tab

. Slightly loosen the filter cup

ring nut

Remove the filter cup

, catching any

spilled fuel in a rag.

Remove the filter element

, and wash

it in solvent.
Allow it to dry. Inspect the filter element
and O-ring

to make sure they are in

good condition. Replace them if neces-
sary.

001603

001578

60V-9-11-4 8/10/02 1:02 PM Page 15

Содержание LZ250B































































































































Результаты поиска

Содержание LZ250B

Отзывы:

Похожие инструкции для LZ250B

Бренды по названию

Популярные бренды

Yamaha LZ250B, Руководство пользователя

Результаты поиска

Содержание LZ250B

Отзывы:

Похожие инструкции для LZ250B

Бренды по названию

Популярные бренды