Yamaha LZ250B Скачать руководство пользователя страница 104

Страница: 104 / 126

EMU01280

Disconnecting the Battery

Disconnect the BLACK lead from the NEG-
ATIVE (-) terminal first. Then disconnect the
RED lead from the POSITIVE (+) terminal.

4-27

Connecting an accessory battery

(option)

Remove the accessory battery coupler
cover from the outboard motor.

Connect the accessory battery coupler

to the coupler of the accessory bat-

tery lead (option).

Use a connecting cable between the (-) ter-
minals of the starting battery and accessory
battery. See the illustrations of the wiring
connections. This cable must be made from
wire thicker than the starting battery cable

Use of smaller wire could lead to a fire.

Battery for starting

Battery for accessories

Large red lead for starting battery

Small red lead for accessory battery charging
(optional part)

Large black lead

Negative connecting cable (optional part)

Power for accessories

NOTE:

If a battery selector switch is desired, con-
sult your YAMAHA dealer about correct
wiring.

001627

001607

y u

60V-9-11-4 8/10/02 1:02 PM Page 28

Содержание LZ250B































































































































Результаты поиска

Содержание LZ250B

Отзывы:

Похожие инструкции для LZ250B

Бренды по названию

Популярные бренды

Yamaha LZ250B, Руководство пользователя

Результаты поиска

Содержание LZ250B

Отзывы:

Похожие инструкции для LZ250B

Бренды по названию

Популярные бренды