Yamaha LZ250B Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 126

background image

E

5-6

EMU01565

LOW OIL LEVEL WARNING
ACTIVATES

If the oil level is allowed to drop too low, the
red segment will appear on the oil level indi-
cator,  the  buzzer  will  sound,  and  engine
speed will be limited to about 2,000 r/min. If
this  happens,  a  reserve  amount  of  oil  can
be  pumped  from  the  remote  oil  tank

3

to

the engine oil tank

2

using the emergency

switch

1

.

w

Be sure to stop the engine before per-
forming this procedure.

c

C

8

If the emergency switch is held up too
long, too much oil will be pumped into
the

engine

tank,

overflowing

it.

Release the switch when oil reaches
the upper level line on the engine oil
tank.

8

Do not use this emergency procedure
unless the oil level warning lamps are
installed and working.

1)

Remove the top cowling.

2)

Turn the main switch to the “ON” posi-
tion.

3)

Lift the emergency switch to pump
reserve oil in remote oil tank into the
engine oil tank.

4)

After  using  the  emergency  switch,  turn
off the main switch, then turn it back on.
This  resets  the  warning  system  to  nor-
mal  operation. The  yellow  segment  will
continue to be displayed on the oil level
indicator.

5)

Start the engine and return to the near-
est port for more oil.

001586

q

001284

e

w

60V-9-11-5 7/31/02 10:28 AM Page 7

«
...
111
112
113
114
115
...
»

Содержание LZ250B































































































































Отзывы:

Нет отзывов

Похожие инструкции для LZ250B

Бренд: Yamaha Страницы: 497

Бренд: AOpen Страницы: 8

Бренд: Xilinx Страницы: 88

Бренд: Biostar Страницы: 37

H470 AORUS PRO AX

Бренд: Gigabyte Страницы: 52

Бренд: AOpen Страницы: 8

STEVAL-LLL002V1

Бренд: STMicroelectronics Страницы: 29

Бренд: FIC Страницы: 68

Бренд: Gigabyte Страницы: 44

Бренд: Texas Instruments Страницы: 34

Бренд: ASROCK Страницы: 139

Бренд: ASROCK Страницы: 25

EVAL-AD4696FMCZ

Бренд: Analog Devices Страницы: 28

Бренд: ASROCK Страницы: 66

Бренд: Suzuki Marine Страницы: 63

Бренд: Siemens Страницы: 15

Бренд: Siemens Страницы: 26

Бренд: Siemens Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды