Yamaha LZ250B Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 126

background image

E

4-2

Z250TRB

LZ250TRB

VZ250TRB

868 (34.2)
568 (22.4)
— / 1,830 (72.0) / 1,957 (77.0)
— / 641 (25.2) / 768 (30.2)
— / 247 (545) / 252 (556)

4,500–5,500
183.9 (250) @ 5,000
670–730

2-stroke, V6
3,342 (203.9)
93.0

×

82.0 (3.66

×

3.23)

TCI system
BKR7EKU
0.5–0.7 (0.02–0.03)
Remote control
Electric start

512
675
182
12-50
Electronic fuel injection

Forward-Neutral-Reverse
1.81 (29/16)
Power trim and tilt
T, M

Regular unleaded gasoline
Minimum 86
—
YAMALUBE 2 STROKE OUTBOARD OIL
oil injection system
1.2 (1.3, 1.1)
10.5 (11.1, 9.2)
Hypoid gear oil (SAE90)
1,150 (38.9, 40.5)

25 (2.55, 18.44)
54 (5.51, 39.83)

868 (34.2)
568 (22.4)
— / 1,830 (72.0) / 1,957 (77.0)
— / 641 (25.2) / 768 (30.2)
— / 247 (545) / 252 (556)

4,500–5,500
183.9 (250) @ 5,000
670–730

2-stroke, V6
3,342 (203.9)
93.0

×

82.0 (3.66

×

3.23)

TCI system
BKR7EKU
0.5–0.7 (0.02–0.03)
Remote control
Electric start

512
675
182
12-50
Electronic fuel injection

Forward-Neutral-Reverse
1.81 (29/16)
Power trim and tilt
TL, ML

Regular unleaded gasoline
Minimum 86
—
YAMALUBE 2 STROKE OUTBOARD OIL
oil injection system
1.2 (1.3, 1.1)
10.5 (11.1, 9.2)
Hypoid gear oil (SAE90)
1,000 (33.8, 35.2)

25 (2.55, 18.44)
54 (5.51, 39.83)

906 (35.7)
568 (22.4)
1,714 (67.5) / — / —
493 (19.4) / — / —
245 (540) / — / —

4,500–5,500
183.9 (250) @ 5,000
700–760

2-stroke, V6
3,342 (203.9)
93.0

×

82.0 (3.66

×

3.23)

TCI system
BKR7EKU
0.5–0.7 (0.02–0.03)
Remote control
Electric start

512
675
182
12-50
Electronic fuel injection

Forward-Neutral-Reverse
1.75 (28/16)
Power trim and tilt
T

Regular unleaded gasoline
Minimum 86
—
YAMALUBE 2 STROKE OUTBOARD OIL
oil injection system
1.2 (1.3, 1.1)
10.5 (11.1, 9.2)
Hypoid gear oil (SAE90)
1,000 (33.8, 35.2)

25 (2.55, 18.44)
54 (5.51, 39.83)

60V-9-11-4 8/10/02 1:02 PM Page 3

«
...
77
78
79
80
81
...
»

Содержание LZ250B































































































































Отзывы:

Нет отзывов

Похожие инструкции для LZ250B

Бренд: Udoo Страницы: 9

Бренд: AOpen Страницы: 8

Бренд: MSI Страницы: 35

Бренд: Arbor Technology Страницы: 86

CONROE1333-ESATA2

Бренд: ASROCK Страницы: 226

Бренд: DFI Страницы: 92

Бренд: ASROCK Страницы: 244

Бренд: Avalue Technology Страницы: 80

Бренд: Apex Digital Страницы: 5

Бренд: Gigabyte Страницы: 23

IMX233-OLX-NANO

Бренд: OLIMEX Страницы: 36

Бренд: Aaeon Страницы: 90

Бренд: DFI Страницы: 118

Бренд: Asus Страницы: 2

EX-H310M-V3 R2.0

Бренд: Asus Страницы: 2

Бренд: Asus Страницы: 64

Бренд: Asus Страницы: 144

Бренд: Asus Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды