Yamaha LZ250B Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 126

background image

E

3-4

Z250, LZ250

Mount the outboard motor so that the anti-
cavitation plate is in alignment with the bot-
tom of the boat.

104014

104025

130mm ( 5 in.)

VZ225, VZ250

Mount the outboard motor so that the anti-
cavitation plate is about 130 mm (5 in.)
above the bottom of the boat.

NOTE:

8

The  optimum  mounting  height  of  the
outboard motor is affected by the boat
and  motor  combination  and  the
desired  use.  Test  runs  at  different
heights  can  help  determine  the  opti-
mum  mounting  height.  Consult  your
Yamaha  dealer  or  boat  manufacturer
for further information on determining
the proper mounting height.

8

For  instructions  on  setting  the  trim
angle  of  the  outboard  motor,  see
“Trimming  outboard  motor”  in  this
chapter.

60V-9-11-3 7/31/02 1:52 PM Page 5

«
...
53
54
55
56
57
...
»

Содержание LZ250B































































































































Отзывы:

Нет отзывов

Похожие инструкции для LZ250B

Бренд: AOpen Страницы: 105

Бренд: Beck Страницы: 24

Бренд: ASROCK Страницы: 30

Бренд: Procomp Страницы: 55

Бренд: J&W Страницы: 40

Бренд: Texas Instruments Страницы: 8

Бренд: Inrevium Страницы: 57

Бренд: Texas Instruments Страницы: 21

Бренд: ON Semiconductor Страницы: 7

Бренд: Biostar Страницы: 67

Бренд: TYAN Страницы: 37

Бренд: Texas Instruments Страницы: 3

Бренд: Gigabyte Страницы: 23

Бренд: ASROCK Страницы: 92

Бренд: BCM Advanced Research Страницы: 72

Бренд: Ublox Страницы: 18

Бренд: SOYO Страницы: 104

Бренд: IEI Technology Страницы: 158

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды