Yamaha LZ250B Скачать руководство пользователя страница 110

Страница: 110 / 126

5-3

Trouble

Possible Cause

Remedy

E. Engine power loss.

13. Poor connections or damaged ignition

wiring.

14. Failed ignition parts.

15. Specified engine oil not used.

16. Thermostat faulty or clogged.

17. Fuel pump damaged.

18. Fuel joint connection incorrect.

19. Heat range of spark plug incorrect.

20. High pressure fuel pump drive belt

broken.

21. Engine not responding properly to shift

lever position.

13. Check wires for wear or breaks.

Tighten all loose connections.

Replace worn or broken wires.

14. Have serviced by a Yamaha dealer.

15. Check and replace oil with specified

type.

16. Have serviced by a Yamaha dealer.

17. Have serviced by a Yamaha dealer.

18. Connect correctly.

19. Inspect spark plug and replace it

with recommended type.

20. Have serviced by a Yamaha dealer.

21. Have serviced by a Yamaha dealer.

F. Engine vibrates

excessively.

1. Propeller damaged.

2. Propeller shaft damaged.

3. Weeds or other foreign matter tangled

on propeller.

4. Motor mounting bolt loose.

5. Steering pivot loose or damaged.

1. Have propeller repaired or replaced.

2. Have serviced by a Yamaha dealer.

3. Remove and clean propeller.

4. Tighten bolt.

5. Tighten or have serviced by a

Yamaha dealer.

60V-9-11-5 7/31/02 10:28 AM Page 4

Содержание LZ250B































































































































Результаты поиска

Содержание LZ250B

Отзывы:

Похожие инструкции для LZ250B

Бренды по названию

Популярные бренды

Yamaha LZ250B, Руководство пользователя

Результаты поиска

Содержание LZ250B

Отзывы:

Похожие инструкции для LZ250B

Бренды по названию

Популярные бренды