Yamaha FZS10A Скачать руководство пользователя | Manualshive

Страница: 37 / 112

background image

INSTRUMENT AND CONTROL FUNCTIONS

4-18

4

Compression damping force

The compression damping force is ad-
justed on the left front fork leg only. To
increase the compression damping
force and thereby harden the compres-
sion damping, turn the adjusting screw
in direction (a). To decrease the com-

pression damping force and thereby
soften the compression damping, turn
the adjusting screw in direction (b).

TIP

Be sure to perform this adjustment on
the left front fork leg.

TIP

Although the total number of clicks of a
damping force adjusting mechanism
may not exactly match the above spec-
ifications due to small differences in
production, the actual number of clicks
always represents the entire adjusting
range. To obtain a precise adjustment,
it would be advisable to check the num-
ber of clicks of each damping force ad-
justing mechanism and to modify the
specifications as necessary.

1. Rebound damping force adjusting screw

Rebound damping setting:

Minimum (soft):

26 click(s) in direction (b)*

Standard:

18 click(s) in direction (b)*

Maximum (hard):

1 click(s) in direction (b)*

* With the adjusting screw fully turned

in direction (a)

1. Compression damping force adjusting screw

Compression damping setting:

Minimum (soft):

26 click(s) in direction (b)*

Standard:

5 click(s) in direction (b)*

Maximum (hard):

1 click(s) in direction (b)*

* With the adjusting screw fully turned

in direction (a)

U1CA11E0.book Page 18 Thursday, September 23, 2010 11:51 AM

«
...
35
36
37
38
39
...
»

Содержание FZS10A

















































































































Отзывы:

Нет отзывов

Похожие инструкции для FZS10A

Бренд: GAS GAS Страницы: 70

Бренд: Öhlins Страницы: 2

Mechatronics 35007-01

Бренд: Öhlins Страницы: 4

McPherson Strut MIR 5H02

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 4

Бренд: Baja motorsports Страницы: 20

Бренд: Clas Ohlson Страницы: 5

Spyder RT Series

Бренд: Can-Am Страницы: 52

Бренд: hepco & becker Страницы: 4

Бренд: G PLAST Страницы: 4

Бренд: Pagsta Страницы: 47

Бренд: Shad Страницы: 2

Бренд: Shad Страницы: 2

TOPMASTER V0NR55ST

Бренд: Shad Страницы: 2

TOPMASTER Y0TM52ST

Бренд: Shad Страницы: 3

Бренд: Shad Страницы: 4

Бренд: Kuberg Страницы: 16

Бренд: Kuberg Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды