Yamaha FZS10A Скачать руководство пользователя | Manualshive

Страница: 60 / 112

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-11

7

TIP

If a torque wrench is not available when
installing a spark plug, a good estimate
of the correct torque is 1/4–1/2 turn
past finger tight. However, the spark
plug should be tightened to the speci-
fied torque as soon as possible.

NOTICE

ECA10840

Do not use any tools to remove or in-
stall the spark plug cap, otherwise
the ignition coil coupler may get
damaged. The spark plug cap may
be difficult to remove because the
rubber seal on the end of the cap fits
tightly. To remove the spark plug
cap, simply twist it back and forth
while pulling it out; to install it, twist
it back and forth while pushing it in.

EAU19681

Canister (for California only)

This model is equipped with a canister
to prevent the discharging of fuel vapor
into the atmosphere. Before operating
this vehicle, make sure to check the fol-
lowing:

●

Check each hose connection.

●

Check each hose and canister for
cracks or damage. Replace if dam-
aged.

●

Make sure that the canister breath-
er is not blocked, and if necessary,
clean it.

EAU19879

Engine oil and oil filter car-
tridge

The engine oil level should be checked
before each ride. In addition, the oil
must be changed and the oil filter car-
tridge replaced at the intervals speci-
fied in the periodic maintenance and
lubrication chart.

To check the engine oil level

1. Place the vehicle on the center-

stand. A slight tilt to the side can
result in a false reading.

2. Start the engine, warm it up for

several minutes, and then turn it
off.

3. Wait a few minutes until the oil set-

tles, and then check the oil level
through the engine oil level check
window located at the bottom-right
side of the crankcase.

TIP

The engine oil should be between the
minimum and maximum level marks.

U1CA11E0.book Page 11 Thursday, September 23, 2010 11:51 AM

«
...
58
59
60
61
62
...
»

Содержание FZS10A

















































































































Отзывы:

Нет отзывов

Похожие инструкции для FZS10A

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 44

B-TRK502-02-01-SL

Бренд: SRC Страницы: 4

Бренд: R&G Страницы: 6

Бренд: N-Com Страницы: 6

Бренд: Wedze Страницы: 63

Бренд: BOXER Страницы: 11

Бренд: KTM Страницы: 207

Бренд: Kabuto Страницы: 19

Бренд: hepco & becker Страницы: 4

Бренд: DYNATEK Страницы: 3

Бренд: DYNATEK Страницы: 6

Бренд: Memphis Shades Страницы: 2

Бренд: Razor Страницы: 3

COMP-MLCS-12200

Бренд: Compcooler Страницы: 11

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды