manualshive.com logo in svg

Yamaha FZS10A, Руководство пользователя

Поделиться
Скачать
Yamaha FZS10A Скачать руководство пользователя страница 74

PERIODIC MAINTENANCE AND ADJUSTMENT

7-25

7

EAU22760

Drive chain slack 

The drive chain slack should be
checked before each ride and adjusted
if necessary.

EAU22794

To check the drive chain slack

1. Place the motorcycle on the cen-

terstand.

2. Shift the transmission into the neu-

tral position.

3. Measure the drive chain slack as

shown.

4. If the drive chain slack is incorrect,

adjust it as follows.

EAU49312

To adjust the drive chain slack

Consult a Yamaha dealer before ad-
justing the drive chain slack.

1. Take the motorcycle off the center-

stand, and then put the sidestand
down.

2. Loosen the axle nut and the lock-

nut on each side of the swingarm.

3. Place the motorcycle on the cen-

terstand.

4. To tighten the drive chain, turn the

drive chain slack adjusting bolt on
each side of the swingarm in direc-
tion (a). To loosen the drive chain,
turn the adjusting bolt on each side
of the swingarm in direction (b),
and then push the rear wheel for-
ward. 

NOTICE:

 Improper drive

chain slack will overload the en-
gine as well as other vital parts
of the motorcycle and can lead
to chain slippage or breakage.
To prevent this from occurring,
keep the drive chain slack with-
in the specified limits.

 [ECA10571]

TIP

Using the alignment marks on each
side of the swingarm, make sure that
both drive chain pullers are in the same
position for proper wheel alignment.

5. Take the motorcycle off the center-

stand, and then put the sidestand
down.

6. Tighten the axle nut, then the lock-

nuts to the specified torques.

1. Drive chain slack

Drive chain slack:

20.0–30.0 mm (0.79–1.18 in)

1. Axle nut

2. Drive chain slack adjusting bolt
3. Locknut

4. Drive chain puller

5. Alignment marks

U1CA11E0.book  Page 25  Thursday, September 23, 2010  11:51 AM

Содержание FZS10A

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды