Yamaha FZS10A Скачать руководство пользователя | Manualshive

Страница: 92 / 112

background image

MOTORCYCLE CARE AND STORAGE

8-1

8

EAU37833

Matte color caution

NOTICE

ECA15192

Some models are equipped with
matte colored finished parts. Be
sure to consult a Yamaha dealer for
advice on what products to use be-
fore cleaning the vehicle. Using a
brush, harsh chemical products or
cleaning compounds when cleaning
these parts will scratch or damage
their surface. Wax also should not
be applied to any matte colored fin-
ished parts.

EAU26014

Care

While the open design of a motorcycle
reveals the attractiveness of the tech-
nology, it also makes it more vulnera-
ble. Rust and corrosion can develop
even if high-quality components are
used. A rusty exhaust pipe may go un-
noticed on a car, however, it detracts
from the overall appearance of a motor-
cycle. Frequent and proper care does
not only comply with the terms of the
warranty, but it will also keep your mo-
torcycle looking good, extend its life
and optimize its performance.

Before cleaning

1. Cover the muffler outlet with a

plastic bag after the engine has
cooled down.

2. Make sure that all caps and covers

as well as all electrical couplers
and connectors, including the
spark plug caps, are tightly in-
stalled.

3. Remove extremely stubborn dirt,

like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such prod-

ucts onto seals, gaskets, sprock-
ets, the drive chain and wheel
axles. Always rinse the dirt and de-
greaser off with water.

Cleaning

NOTICE

ECA10772

●

Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the af-
fected area any longer than in-
structed. Also, thoroughly rinse
the area off with water, immedi-
ately dry it, and then apply a cor-
rosion protection spray.

●

Improper cleaning can damage
plastic parts (such as cowlings,
panels, windshields, headlight
lenses, meter lenses, etc.) and
the mufflers. Use only a soft,
clean cloth or sponge with wa-
ter to clean plastic. However, if
the plastic parts cannot be thor-
oughly cleaned with water, di-
luted mild detergent with water
may be used. Be sure to rinse

U1CA11E0.book Page 1 Thursday, September 23, 2010 11:51 AM

«
...
90
91
92
93
94
...
»

Содержание FZS10A

















































































































Отзывы:

Нет отзывов

Похожие инструкции для FZS10A

Бренд: HYOSUNG Страницы: 98

Бренд: BV Powersports Страницы: 40

Бренд: NewMar Страницы: 116

Бренд: R&G Страницы: 12

Бренд: LSL Страницы: 12

Бренд: Kabuto Страницы: 19

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 144

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 255

Бренд: Yamaha Страницы: 17

Бренд: Yamaha Страницы: 596

Бренд: Yamaha Страницы: 578

Бренд: DYNATEK Страницы: 12

Бренд: Cobra Страницы: 2

Бренд: Dynafit Страницы: 21

Бренд: APRILIA Страницы: 216

Бренд: Wunderkind Custom Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды