Yamaha FZS10A Скачать руководство пользователя | Manualshive

Страница: 67 / 112

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-18

7

EAU21384

Checking the throttle grip free
play

The throttle grip free play should mea-
sure 3.0–5.0 mm (0.12–0.20 in) at the
inner edge of the throttle grip. Periodi-
cally check the throttle grip free play
and, if necessary, have a Yamaha deal-
er adjust it.

EAU21401

Valve clearance

The valve clearance changes with use,
resulting in improper air-fuel mixture
and/or engine noise. To prevent this
from occurring, the valve clearance
must be adjusted by a Yamaha dealer
at the intervals specified in the periodic
maintenance and lubrication chart.

EAU21755

Tires

To maximize the performance, durabil-
ity, and safe operation of your motorcy-
cle, note the following points regarding
the specified tires.

Tire air pressure

The tire air pressure should be checked
and, if necessary, adjusted before each
ride.

WARNING

EWA10503

Operation of this vehicle with im-
proper tire pressure may cause se-
vere injury or death from loss of
control.

●

The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the temperature
of the tires equals the ambient
temperature).

●

The tire air pressure must be ad-
justed in accordance with the
riding speed and with the total
weight of rider, passenger, car-
go, and accessories approved
for this model.

1. Throttle grip free play

U1CA11E0.book Page 18 Thursday, September 23, 2010 11:51 AM

«
...
65
66
67
68
69
...
»

Содержание FZS10A

















































































































Отзывы:

Нет отзывов

Похожие инструкции для FZS10A

Бренд: MadStad Engineering Страницы: 2

Бренд: Kabuto Страницы: 12

Бренд: Memphis Shades Страницы: 2

Бренд: LAMAX Страницы: 134

Бренд: Ohlins Страницы: 8

Бренд: GAS GAS Страницы: 119

Бренд: Honda Страницы: 3

Бренд: Ice Bear Страницы: 64

Бренд: PUIG Страницы: 3

Бренд: Norton Страницы: 69

Бренд: VESPA Страницы: 64

Бренд: Power Fist Страницы: 20

DORSODURO - 2009

Бренд: APRILIA Страницы: 9

TORNADO Tre Novecento 900

Бренд: Benelli Страницы: 48

Бренд: Benelli Страницы: 108

Бренд: APRILIA Страницы: 264

Бренд: KTM Страницы: 12

Бренд: KTM Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды