manualshive.com logo in svg

Yamaha FZS10A, Руководство пользователя

Поделиться
Скачать
Yamaha FZS10A Скачать руководство пользователя страница 83

PERIODIC MAINTENANCE AND ADJUSTMENT

7-34

7

EAU23933

Replacing a headlight bulb 

This model is equipped with halogen
bulb headlights. If a headlight bulb
burns out, replace it as follows.

NOTICE

ECA10650

Take care not to damage the follow-
ing parts:

●

Headlight bulb
Do not touch the glass part of
the headlight bulb to keep it free
from oil, otherwise the transpar-
ency of the glass, the luminosity
of the bulb, and the bulb life will
be adversely affected. Thor-
oughly clean off any dirt and fin-
gerprints on the headlight bulb
using a cloth moistened with al-
cohol or thinner.

●

Headlight lens
Do not affix any type of tinted
film or stickers to the headlight
lens.
Do not use a headlight bulb of a
wattage higher than specified.

1. Disconnect the headlight coupler,

and then remove the bulb cover.

2. Unhook the headlight bulb holder,

and then remove the burnt-out
bulb.

3. Place a new headlight bulb into po-

sition, and then secure it with the
bulb holder.

4. Install the headlight bulb cover,

and then connect the coupler.

5. Have a Yamaha dealer adjust the

headlight beam if necessary.

1. Do not touch the glass part of the bulb.

1. Headlight coupler

2. Headlight bulb cover

1. Headlight bulb holder

U1CA11E0.book  Page 34  Thursday, September 23, 2010  11:51 AM

Содержание FZS10A

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды