Yamaha FZS10A Скачать руководство пользователя | Manualshive

Страница: 64 / 112

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-15

7

If water has been used instead
of coolant, replace it with cool-
ant as soon as possible, other-
wise the cooling system will not
be protected against frost and
corrosion. If water has been
added to the coolant, have a
Yamaha dealer check the anti-
freeze content of the coolant as
soon as possible, otherwise the
effectiveness of the coolant will
be reduced.

[ECA10472]

5. Install the panel.

EAU33031

Changing the coolant

The coolant must be changed at the in-
tervals specified in the periodic mainte-
nance and lubrication chart. Have a
Yamaha dealer change the coolant.

WARNING! Never attempt to remove
the radiator cap when the engine is
hot.

[EWA10381]

EAU40054

Replacing the air filter element

The air filter element should be re-
placed at the intervals specified in the
periodic maintenance and lubrication
chart. Replace the air filter element
more frequently if you are riding in un-
usually wet or dusty areas.

1. Remove the rider seat. (See page

2. Remove panels A and B. (See

3. Remove the fuel tank cowling

bolts, and then pull the fuel tank
cowling off.

4. Remove the fuel tank bolts.

1. Coolant reservoir cap

Coolant reservoir capacity (up to
the maximum level mark):

0.25 L (0.26 US qt, 0.22 Imp.qt)

1. Fuel tank cowling

2. Fuel tank cowling bolt

U1CA11E0.book Page 15 Thursday, September 23, 2010 11:51 AM

«
...
62
63
64
65
66
...
»

Содержание FZS10A

















































































































Отзывы:

Нет отзывов

Похожие инструкции для FZS10A

Бренд: Fantic Motor Страницы: 130

Бренд: UNIT 1 Страницы: 23

Бренд: Kabuto Страницы: 16

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 44

Бренд: R&G Страницы: 4

Бренд: X-lite Страницы: 76

Бренд: Wedze Страницы: 63

Бренд: Spartus Страницы: 24

Lock-it TANKRING 506003

Бренд: hepco & becker Страницы: 2

SUPERSPORT1000 2003

Бренд: Ducati Страницы: 328

SCARABEO 100 4T - 06-2001 PART6

Бренд: APRILIA Страницы: 6

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 88

TDM850'99 4TX-AE3

Бренд: Yamaha Страницы: 43

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 105

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды