manualshive.com logo in svg

Yamaha FZS10A, Руководство пользователя

Поделиться
Скачать
Yamaha FZS10A Скачать руководство пользователя страница 79

PERIODIC MAINTENANCE AND ADJUSTMENT

7-30

7

NOTICE

ECA10590

If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-
pair it.

EAU45511

Checking the steering 

Worn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as fol-
lows at the intervals specified in the pe-
riodic maintenance and lubrication
chart.

1. Place the vehicle on the center-

stand. 

WARNING! To avoid inju-

ry, securely support the vehicle
so there is no danger of it falling
over.

 [EWA10751]

2. Hold the lower ends of the front

fork legs and try to move them for-
ward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steering.

EAU23291

Checking the wheel bearings 

The front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and lubrica-
tion chart. If there is play in the wheel
hub or if the wheel does not turn
smoothly, have a Yamaha dealer check
the wheel bearings.

U1CA11E0.book  Page 30  Thursday, September 23, 2010  11:51 AM

Содержание FZS10A

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды