Yamaha FZS10A Скачать руководство пользователя

Страница: 85 / 112

PERIODIC MAINTENANCE AND ADJUSTMENT

7-36

EAU24313

Replacing the license plate
light bulb

1. Remove the license plate light unit

by removing the screws.

2. Remove the license plate light bulb

socket (together with the bulb) by
pulling it out.

3. Remove the burnt-out bulb by pull-

ing it out.

4. Insert a new bulb into the socket.
5. Install the socket (together with the

bulb) by pushing it in.

6. Install the license plate light unit by

installing the screws.

EAU24360

Front wheel

EAU40201

To remove the front wheel

WARNING

EWA10821

To avoid injury, securely support the
vehicle so there is no danger of it
falling over.

1. Place the vehicle on the center-

stand.

2. Loosen the front wheel axle pinch

bolt, then the wheel axle and the
brake caliper bolts.

1. License plate light unit

2. Screw

1. License plate light bulb
2. License plate light bulb socket

1. Front wheel axle pinch bolt

2. Wheel axle
3. Brake caliper bolt

U1CA11E0.book Page 36 Thursday, September 23, 2010 11:51 AM

Содержание FZS10A

















































































































Результаты поиска

Содержание FZS10A

Отзывы:

Похожие инструкции для FZS10A

Бренды по названию

Популярные бренды

Yamaha FZS10A, Руководство пользователя

Результаты поиска

Содержание FZS10A

Отзывы:

Похожие инструкции для FZS10A

Бренды по названию

Популярные бренды