Yamaha F13.5B Скачать руководство пользователя | Manualshive

Страница: 21 / 90

background image

Basic components

15

EMU26190

Remote control lever

Moving the lever forward from the neutral po-
sition engages forward gear. Pulling the le-
ver back from neutral engages reverse. The
engine will continue to run at idle until the le-
ver is moved about 35° (a detent can be felt).
Moving the lever farther opens the throttle,
and the engine will begin to accelerate.

EMU26201

Neutral interlock trigger

To shift out of neutral, first pull the neutral in-
terlock trigger up.

EMU26211

Neutral throttle lever

To open the throttle without shifting into ei-
ther forward or reverse, put the remote con-
trol lever in the neutral position and lift the
neutral throttle lever.

NOTE:

The neutral throttle lever will operate only
when the remote control lever is in neutral.
The remote control lever will operate only
when the neutral throttle lever is in the closed

position.

EMU25911

Tiller handle

To change direction, move the tiller handle to
the left or right as necessary.

1. Neutral “ ”

2. Forward “ ”

3. Reverse “ ”
4. Shift
5. Fully closed
6. Throttle
7. Fully open

1. Neutral interlock trigger

1. Fully open
2. Fully closed

«
...
19
20
21
22
23
...
»

Содержание F13.5B



























































































Отзывы:

Нет отзывов

Похожие инструкции для F13.5B

XRP7664-65-74-75

Бренд: Exar Страницы: 8

CYTVII-B-E-1M-SK

Бренд: Cypress Страницы: 19

Бренд: Zotac Страницы: 54

Бренд: Yamaha Страницы: 223

Бренд: Acorp Страницы: 74

Бренд: MSI Страницы: 104

Бренд: Apex Digital Страницы: 5

Бренд: JETWAY Страницы: 48

Бренд: Texas Instruments Страницы: 34

Бренд: MSI Страницы: 106

Thunder HEsl S2567

Бренд: TYAN Страницы: 60

Бренд: Aaeon Страницы: 78

Бренд: Zamel Страницы: 3

Бренд: Fujitsu Siemens Computers Страницы: 21

Бренд: Yamaha Страницы: 124

Бренд: Yamaha Страницы: 122

Бренд: Yamaha Страницы: 90

Бренд: TYAN Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды