Yamaha F13.5B страница 10 Скачать руководство пользователя

Страница: 10 / 90

General information

EMU33911

Contents of labels

The above warning labels mean as follows.

WARNING

EWM01690

Emergency starting does not have start-
in-gear protection. Ensure shift control is

in neutral before starting engine.

WARNING

EWM01680

●

Keep hands, hair, and clothing away
from rotating parts while the engine is
running.

●

Do not touch or remove electrical parts

when starting or during operation.

WARNING

EWM01670

●

Read Owner’s Manuals and labels.

●

Wear an approved personal flotation
device (PFD).

●

Attach engine shut-off cord (lanyard) to
your PFD, arm, or leg so the engine
stops if you accidentally leave the
helm, which could prevent a runaway

boat.

EMU33841

Symbols

The following symbols mean as follows.

Caution/Warning

ZMU05706

Содержание F13.5B



























































































Результаты поиска

Содержание F13.5B

Отзывы:

Похожие инструкции для F13.5B

Бренды по названию

Популярные бренды

Yamaha F13.5B, Руководство пользователя

Результаты поиска

Содержание F13.5B

Отзывы:

Похожие инструкции для F13.5B

Бренды по названию

Популярные бренды