Yamaha F13.5B страница 30 Скачать руководство пользователя

Страница: 30 / 90

Basic components

If the warning system has activated, stop the
engine and check the cooling water inlet for
clogging.

EMU30168

Low oil pressure warning

If the oil pressure drops too low, the warning
device will activate.

Activation of warning device

●

The engine speed will automatically de-
crease to about 2000 r/min.

●

If equipped with a low oil pressure-warning
indicator, it will light or blink.

●

The buzzer will sound (if equipped on the
tiller handle, remote control box, or main
switch panel).

If the warning system has activated, stop the
engine as soon as it is safe to do so. Check
the oil level and add oil as needed. If the oil
level is correct and the warning device does
not switch off, consult your Yamaha dealer.

CAUTION:

ECM00101

Do not continue to run the engine if the
low oil pressure-warning indicator is on.

Serious engine damage could occur.

ZMU03026

ZMU05531

ZMU02360

Содержание F13.5B



























































































Результаты поиска

Содержание F13.5B

Отзывы:

Похожие инструкции для F13.5B

Бренды по названию

Популярные бренды

Yamaha F13.5B, Руководство пользователя

Результаты поиска

Содержание F13.5B

Отзывы:

Похожие инструкции для F13.5B

Бренды по названию

Популярные бренды