Yamaha F13.5B страница 58 Скачать руководство пользователя | Manualshive

Страница: 58 / 90

background image

Maintenance

52

the attitude shown when transporting
and storing it. If storing or transporting
the outboard motor on its side (not up-
right), put it on a cushion after draining
the engine oil.

●

Do not place the outboard motor on its
side before the cooling water has
drained from it completely, otherwise
water may enter the cylinder through
the exhaust port and cause engine trou-
ble.

●

Store the outboard motor in a dry, well-

ventilated place, not in direct sunlight.

EMU28303

Procedure

EMU32021

Flushing in a test tank

CAUTION:

ECM00300

Do not run the engine without supplying
it with cooling water. Either the engine
water pump will be damaged or the en-
gine will be damaged from overheating.
Before starting the engine, be sure to
supply water to the cooling water passag-

es.

1.

Dismount the outboard motor from the
boat. For further details, see page 50.

2.

Wash the outboard motor body using
fresh water. For further information, see
page 55.

3.

Disconnect the fuel line from the out-
board motor.

4.

Remove the engine top cowling and si-
lencer cover. Remove the propeller. For
further details, see page 68.

5.

Position the outboard motor on a water
tank. For further details, see page 25.

6.

Fill the tank with fresh water until the
anti-cavitation plate is immersed in wa-
ter.

CAUTION:

ECM00290

If the fresh water level is below the level
of the anti-cavitation plate, or if the water
supply is insufficient, engine seizure may

occur.

7.

Cooling system flushing is essential to
prevent the cooling system from clog-
ging up with salt, sand, or dirt. In addi-
tion, fogging/lubricating of the engine is
mandatory to prevent excessive engine
damage due to rust. Perform the flush-
ing and fogging at the same time.

WARNING

EWM00090

●

Do not touch or remove electrical parts
when starting or during operation.

●

Keep hands, hair, and clothes away
from the flywheel and other rotating

parts while the engine is running.

8.

Run the engine at a fast idle for a few
minutes in neutral position.

9.

Just prior to turning off the engine, quick-
ly spray “Fogging Oil” alternately into
each carburetor or the fogging hole of
the silencer cover, if equipped. When
properly done, the engine will smoke ex-

1. Water surface
2. Lowest water level

ZMU02051

1

2

«
...
56
57
58
59
60
...
»

Содержание F13.5B



























































































Отзывы:

Нет отзывов

Похожие инструкции для F13.5B

Бренд: IEI Technology Страницы: 177

Бренд: Avalue Technology Страницы: 12

Бренд: MIPS Страницы: 10

Бренд: Phytec Страницы: 128

Бренд: Sapphire Audio Страницы: 50

Бренд: J&W Страницы: 28

Бренд: DFI Страницы: 99

Бренд: Texas Instruments Страницы: 101

Бренд: IEI Technology Страницы: 140

DUOX Programmer

Бренд: Fermax Страницы: 99

KEMX-1600 Series

Бренд: Quanmax Страницы: 74

Бренд: VIA Technologies Страницы: 86

Бренд: ASROCK Страницы: 160

Бренд: National Semiconductor Страницы: 22

Бренд: ASROCK Страницы: 200

Бренд: Embedian Страницы: 70

Super 7 SY-5SSM

Бренд: SOYO Страницы: 86

Бренд: Gigabyte Страницы: 143

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды