manualshive.com logo in svg

Yamaha F13.5B, Руководство пользователя

Поделиться
Скачать
Yamaha F13.5B Скачать руководство пользователя страница 86

 

Trouble Recovery

 

80

 

6.

Insert the knotted end of the emergency
starter rope into the notch in the flywheel
rotor and wind the rope 1 or 2 turn(s)
around the flywheel clockwise.

7.

Pull the rope slowly until resistance is
felt. Give a strong pull straight out to
crank and start the engine. If the engine
does not start on the first try, repeat the
procedure.

NOTE:

 

●

 

If the engine does not start on the first try,
repeat the procedure. If the engine fails to
start after 4 or 5 tries, open the throttle a
small amount (between 1/8 and 1/4) and
try again. Also if the engine is warm and
fails to start, open the throttle a same
amount and try to start the engine again. If
the engine still fails to start, see page 31.

 

●

 

Slowly return the throttle grip to the fully
closed position so that the engine does not

 

stall.

 

EMU32003

 

Emergency starting engine (electric 
start model)

 

1.

Remove the top cowling.

2.

Remove the dust cover.

3.

Remove the electrical system cover by
removing its screw(s).

4.

Remove the screw(s) from the plate,

ZMU05533

N

ZMU02026

ZMU05610

ZMU05611

ZMU05612

Содержание F13.5B



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды