Yamaha F13.5B страница 75 Скачать руководство пользователя | Manualshive

Страница: 75 / 90

background image

Maintenance

69

specified torque.

4.

Align the propeller nut with the propeller
shaft hole. Insert a new cotter pin in the
hole and bend the cotter pin ends.

NOTE:

If the propeller nut does not align with the
propeller shaft hole after tightening to the
specified torque, tighten the nut further to

align it with the hole.

EMU29282

Changing gear oil

WARNING

EWM00800

●

Be sure the outboard motor is securely
fastened to the transom or a stable
stand. You could be severely injured if
the outboard motor falls on you.

●

Never get under the lower unit while it
is tilted, even when the tilt support lever
or knob is locked. Severe injury could
occur if the outboard motor accidental-

ly falls.

1.

Tilt the outboard motor so that the gear
oil drain screw is at the lowest point pos-
sible.

2.

Place a suitable container under the
gear case.

3.

Remove the gear oil drain screw and
gasket.

NOTE:

●

If a magnetic gear oil drain screw is
equipped, remove all metal particles from
the screw before installing it.

●

Always use new gaskets. Do not reuse the

removed gaskets.

4.

Remove the oil level plug and gasket to
allow the oil to drain completely.

CAUTION:

ECM00710

Inspect the used oil after it has been
drained. If the oil is milky, water is getting
into the gear case which can cause gear
damage. Consult a Yamaha dealer for re-

pair of the lower unit seals.

NOTE:

For disposal of used oil, consult your

Yamaha dealer.

5.

With the outboard motor in a vertical po-
sition, and using a flexible or pressur-
ized filling device, inject the gear oil into

Propeller nut tightening torque:

17.0 Nm (12.5 ft-lb) (1.73 kgf-m)

ZMU02063

1. Gear oil drain screw
2. Oil level plug

ZMU02064

2

1

«
...
73
74
75
76
77
...
»

Содержание F13.5B



























































































Отзывы:

Нет отзывов

Похожие инструкции для F13.5B

Airborne WLNN-EK-DP55x

Бренд: B&B Electronics Страницы: 6

Бренд: Texas Instruments Страницы: 18

Бренд: Nuvoton Страницы: 14

Бренд: ON Semiconductor Страницы: 19

Tiger MPX S2466

Бренд: TYAN Страницы: 1

Бренд: NXP Semiconductors Страницы: 12

Бренд: Fujitsu Siemens Computers Страницы: 20

EVAL-6ED100HPDRIVE-AS

Бренд: Infineon Страницы: 14

Бренд: Commell Страницы: 53

Бренд: Texas Instruments Страницы: 20

Бренд: MSI Страницы: 90

Бренд: Supermicro Страницы: 88

Бренд: ASROCK Страницы: 38

IMX233-OLX-NANO

Бренд: OLIMEX Страницы: 36

Бренд: Aaeon Страницы: 90

Бренд: MSI Страницы: 58

G31M-GS R2.0-QVL

Бренд: ASROCK Страницы: 2

Бренд: BCM Advanced Research Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды