Yamaha F13.5B страница 84 Скачать руководство пользователя | Manualshive

Страница: 84 / 90

background image

Trouble Recovery

78

EMU32130

Power tilt will not operate

If the engine cannot be tilted up or down with
the power tilt because of a discharged bat-
tery or a failure with the power tilt unit, the
engine can be tilted manually.
1.

Loosen the manual valve screw by turn-
ing it counterclockwise until it stops.

2.

Put the engine in the desired position,
then tighten the manual valve screw by
turning it clockwise.

EMU29533

Starter will not operate

If the starter mechanism does not operate
(the engine cannot be cranked with the start-
er), the engine can be started with an emer-
gency starter rope.

WARNING

EWM01022

●

Use this procedure only in an emergen-
cy to return to the nearest port for re-
pairs.

●

When the emergency starter rope is
used to start the engine, the start-in-
gear protection device does not oper-
ate. Make sure the remote control lever
is in neutral. Otherwise the boat could
unexpectedly start to move, which
could result in an accident.

●

Attach the engine shut-off cord to a se-
cure place on your clothing, or your
arm or leg while operating the boat.

●

Do not attach the cord to clothing that
could tear loose. Do not route the cord
where it could become entangled, pre-
venting it from functioning.

●

Avoid accidentally pulling the cord dur-

1. Fuse puller
2. Cap
3. Fuse (20 A)
4. Spare fuse (20 A)

1. Fuse puller
2. Fuse (20 A)

ZMU05565

1

2

3

4

1

2

ZMU03562

1. Manual valve screw

«
...
82
83
84
85
86
...
»

Содержание F13.5B



























































































Отзывы:

Нет отзывов

Похожие инструкции для F13.5B

Бренд: NXP Semiconductors Страницы: 14

MYC-C8MMQ6-8E2D-160-I

Бренд: MYiR Страницы: 50

Бренд: Gigabyte Страницы: 40

Бренд: Microchip Technology Страницы: 52

Бренд: MediaQ Страницы: 25

Бренд: Supermicro Страницы: 256

Бренд: ASROCK Rack Страницы: 93

Бренд: IEI Technology Страницы: 153

Бренд: Vox Страницы: 23

DiskOnChip PCI-G-EVB

Бренд: M-system Страницы: 14

Бренд: FIC Страницы: 52

Бренд: Biostar Страницы: 31

Бренд: TYAN Страницы: 164

Бренд: Intel Страницы: 87

Бренд: Supermicro Страницы: 88

D850MV - Desktop Board Motherboard

Бренд: Intel Страницы: 25

Бренд: ASROCK Страницы: 106

Бренд: Supermicro Страницы: 107

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды