Yamaha F13.5B Скачать руководство пользователя | Manualshive

Страница: 72 / 90

background image

Maintenance

66

5.

Start the engine and watch to make sure
the low oil pressure-warning indicator (if
equipped) turns off. Make sure that
there are no oil leaks.

CAUTION:

ECM00681

If the low oil pressure-warning indicator
does not turn off or if there are oil leaks,
stop the engine and find the cause. Con-
tinued operation with a problem could
cause severe engine damage. Consult
your Yamaha dealer if the problem can-

not be located and corrected.

6.

Turn off the engine and wait 3 minutes.
Recheck the oil level using the dipstick
to be sure the level falls between the up-
per and lower marks. Fill with oil if it is
below the lower mark, or drain to the
specified level if it is above the upper
mark.

7.

Dispose of used oil according to local
regulations.

NOTE:

●

For more information on the disposal of
used oil, consult your Yamaha dealer.

●

Change the oil more often when operating
the engine under adverse conditions such

as extended trolling.

EMU29112

Checking wiring and connectors

●

Check that each grounding wire is properly
secured.

●

Check that each connector is engaged se-
curely.

EMU29120

Exhaust leakage

Start the engine and check that no exhaust
leaks from the joints between the exhaust
cover, cylinder head, and body cylinder.

1. Oil filler cap

ZMU05562

1

ZMU02058

ZMU02087

«
...
70
71
72
73
74
...
»

Содержание F13.5B



























































































Отзывы:

Нет отзывов

Похожие инструкции для F13.5B

Бренд: Supero Страницы: 80

Бренд: Advantech Страницы: 82

Бренд: ASROCK Страницы: 200

Бренд: Gigabyte Страницы: 112

Бренд: Texas Instruments Страницы: 17

Бренд: AIC Страницы: 58

P35D3 Platinum - Motherboard - ATX

Бренд: MSI Страницы: 104

Бренд: JETWAY Страницы: 46

Бренд: Biostar Страницы: 210

Бренд: ASROCK Страницы: 92

CT-PBT01 Series

Бренд: C&T Solution Страницы: 48

Бренд: ASROCK Страницы: 47

Бренд: Intel Страницы: 62

Бренд: Silicon Laboratories Страницы: 12

Бренд: MSI Страницы: 180

Бренд: TYAN Страницы: 74

Бренд: DFI Страницы: 59

Бренд: DFI Страницы: 115

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды