Yamaha F13.5B Скачать руководство пользователя | Manualshive

Страница: 17 / 90

background image

Basic requirements

11

electric system could perform poorly or
be overloaded, causing electric system

damage.

For electric start models, choose a battery
which meets the following specifications.

EMU25721

Battery specifications

The engine cannot be started if battery volt-
age is too low.

EMU25730

Without a rectifier or Rectifier
Regulator

CAUTION:

ECM01090

A battery cannot be connected to models
that do not have a rectifier or Rectifier

Regulator.

If you wish to use a battery with the models
without a rectifier or Rectifier Regulator, in-
stall an optional Rectifier Regulator.
Using a maintenance-free battery with the

above models can shorten the life of the bat-
tery significantly.
Install an optional Rectifier Regulator or use
accessories rated to withstand 18 volts or
higher with the above models. Consult your
Yamaha dealer for details on installing an
optional Rectifier Regulator.

EMU34190

Propeller selection

Next to selecting an outboard, choosing the
right propeller is one of the most important
purchasing decisions a boater can make.
The type, size, and design of your propeller
have a direct impact on acceleration, top
speed, fuel economy, and even engine life.
Yamaha designs and manufactures propel-
lers for every Yamaha outboard motor and
every application.
Your outboard motor came with a Yamaha
propeller chosen to perform well over a
range of applications, but there may be uses
where a different propeller would be more
appropriate.
Your Yamaha dealer can help you select the
right propeller for your boating needs. Select
a propeller that will allow the engine to reach
the middle or upper half of the operating
range at full throttle with the maximum boat-
load. Generally, chose a larger pitch propel-
ler for a smaller operating load and a smaller
pitch propeller for a heavier load. If you carry
loads that vary widely, chose the propeller
that lets the engine run in the proper range
for your maximum load but remember that
you may need to reduce your throttle setting
to stay within the recommended engine
speed range when carrying lighter loads.
For instructions on propeller removal and in-
stallation, see page 67.

Minimum cold cranking amps (CCA/EN):

F13.5BEH 347.0 A
F13.5BEP 347.0 A
F15CE 347.0 A
F15CEH 347.0 A
F15CEP 347.0 A
F20BE 347.0 A
F20BEH 347.0 A
F20BEP 347.0 A

Minimum rated capacity (20HR/IEC):

F13.5BEH 40.0 Ah
F13.5BEP 40.0 Ah
F15CE 40.0 Ah
F15CEH 40.0 Ah
F15CEP 40.0 Ah
F20BE 40.0 Ah
F20BEH 40.0 Ah
F20BEP 40.0 Ah

«
...
15
16
17
18
19
...
»

Содержание F13.5B



























































































Отзывы:

Нет отзывов

Похожие инструкции для F13.5B

Бренд: NXP Semiconductors Страницы: 6

IP-M945A SERIES

Бренд: WEALTHTEC Страницы: 72

Бренд: Phytec Страницы: 128

Бренд: Sapphire Audio Страницы: 50

Бренд: Analog Devices Страницы: 24

MBATX-845GV-VEAH

Бренд: Kontron Страницы: 70

Бренд: JETWAY Страницы: 44

Бренд: Aaeon Страницы: 44

VECTOR 1 MOTHERBOARD

Бренд: Vector Graphic Страницы: 14

ISL70321SEHDEMO1Z

Бренд: Intersil Страницы: 9

Бренд: MSI Страницы: 91

Бренд: Supermicro Страницы: 111

GA-H170M-HD3 DDR3

Бренд: Gigabyte Страницы: 44

Бренд: Gigabyte Страницы: 96

Бренд: Supermicro Страницы: 84

Бренд: Supermicro Страницы: 95

Бренд: Gigabyte Страницы: 39

Бренд: Biostar Страницы: 67

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды