Yamaha F115D Скачать руководство пользователя страница 60

Страница: 60 / 82

Maintenance

specified level if it is above the upper
mark.

Dispose of used oil according to local
regulations.

NOTE:

●

For more information on the disposal of
used oil, consult your Yamaha dealer.

●

Change the oil more often when operating
the engine under adverse conditions such

as extended trolling.

EMU29111

Checking wiring and connectors

●

Check that each grounding wire is properly
secured.

●

Check that each connector is engaged se-
curely.

EMU29120

Exhaust leakage

Start the engine and check that no exhaust
leaks from the joints between the exhaust
cover, cylinder head, and body cylinder.

EMU29130

Water leakage

Start the engine and check that no water
leaks from the joints between the exhaust
cover, cylinder head, and body cylinder.

EMU29140

Engine oil leakage

Check for oil leaks on the around the engine.

NOTE:

If any leaks are found, consult your Yamaha

dealer.

EMU29153

Checking power trim and tilt system

WARNING

EWM00430

●

Never get under the lower unit while it
is tilted, even when the tilt support lever
is locked. Severe injury could occur if
the outboard motor accidentally falls.

●

Make sure no one is under the outboard

motor before performing this test.

Check the power trim and tilt unit for any
sign of oil leaks.

Operate each of the power trim and tilt
switches on the remote control and en-
gine bottom cowling (if equipped) to
check that all switches work.

Tilt the outboard motor up and check
that the tilt rod and trim rods are extend-
ed completely.

ZMU02058

ZMU04286

1. Tilt rod

ZMU02633

Содержание F115D



















































































Результаты поиска

Содержание F115D

Отзывы:

Похожие инструкции для F115D

Бренды по названию

Популярные бренды

Yamaha F115D, Руководство пользователя

Результаты поиска

Содержание F115D

Отзывы:

Похожие инструкции для F115D

Бренды по названию

Популярные бренды