Yamaha F115D Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 82

background image

Basic components

20

EMU26600

Speedometer (digital type)

This gauge shows the boat speed.

NOTE:

After the main switch is first turned on, all
segments of the display come on as a test.
After a few seconds, the gauge will change
to normal operation. Watch the gauge when
turning on the main switch to make sure all

segments come on.

NOTE:

The speedometer displays km/h, mph, or
knots, according to operator preference. Se-
lect the desired unit of measurement by set-
ting the selector switch on the back of the

gauge. See the illustration for settings.

EMU26610

Trim meter

This gauge shows the trim angle of your out-
board motor.

NOTE:

Memorize the trim angles that work best for
your boat under different conditions. Adjust
the trim angle to the desired setting with the

power trim and tilt switch.

EMU26620

Trim meter (digital type)

This meter shows the trim angle of your out-
board motor.

NOTE:

●

Memorize the trim angles that work best
for your boat under different conditions.
Adjust the trim angle to the desired using

1. Speedometer
2. Fuel gauge
3. Trip meter/clock/voltmeter
4. Warning indicator(s)

1. Cap
2. Selector switch (for speed unit)
3. Selector switch (for fuel sensor)

ZMU04581

«
...
23
24
25
26
27
...
»

Содержание F115D



















































































Отзывы:

Нет отзывов

Похожие инструкции для F115D

Бренд: Xilinx Страницы: 23

Бренд: Xilinx Страницы: 60

Бренд: Xilinx Страницы: 41

Zynq UltraScale+ ZCU104

Бренд: Xilinx Страницы: 92

Zynq UltraScale+ ZCU104

Бренд: Xilinx Страницы: 4

Spartan-3A DSP FPGA Series

Бренд: Xilinx Страницы: 10

Бренд: Xilinx Страницы: 92

Бренд: MSI Страницы: 104

Бренд: A&D Страницы: 4

C5535 DSPShield

Бренд: Texas Instruments Страницы: 49

Бренд: EPOX Страницы: 84

Бренд: Merit Страницы: 4

Бренд: ECS Страницы: 66

Бренд: TOHATSU Страницы: 52

Бренд: Nuvoton Страницы: 11

Бренд: Gigabyte Страницы: 38

Бренд: Gigabyte Страницы: 120

Бренд: Supermicro Страницы: 119

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды