Yamaha F115D Скачать руководство пользователя страница 22

Страница: 22 / 82

Basic components

EMU26340

Tilt support lever for power trim and
tilt or hydro tilt model

To keep the outboard motor in the tilted up
position, lock the tilt support lever to the
clamp bracket.

EMU26382

Top cowling lock lever (pull up type)

To remove the engine top cowling, pull up
the lock lever(s) and lift off the cowling.
When installing the cowling, check to be sure
it fits properly in the rubber seal. Then lock
the cowling by moving the lever(s) down-
ward.

EMU26460

Flushing device

This device is used to clean the cooling wa-
ter passages of the motor using a garden
hose and tap water.

NOTE:

For details on usage, see page 46.

1. Trim tab
2. Bolt
3. Cap

1. Tilt support lever

ZMU02525

ZMU01863

ZMU03979

1. Top cowling lock lever(s)

ZMU04225

ZMU04226

Содержание F115D



















































































Результаты поиска

Содержание F115D

Отзывы:

Похожие инструкции для F115D

Бренды по названию

Популярные бренды

Yamaha F115D, Руководство пользователя

Результаты поиска

Содержание F115D

Отзывы:

Похожие инструкции для F115D

Бренды по названию

Популярные бренды