Yamaha F115D Скачать руководство пользователя страница 53

Страница: 53 / 82

Maintenance

EMU30560

Maintenance chart

NOTE:

●

Refer to the sections in this chapter for explanations of each owner-specific action.

●

The maintenance cycle on these charts assume usage of 200 hours per year. Maintenance
frequency should be adjusted according to usage conditions.

●

Disassembly or repairs may be necessary depending on the outcome of maintenance
checks.

●

Expendable or consumable parts and lubricants will lose their effectiveness over time and

through normal usage regardless of the warranty period.

The “

” symbol indicates the check-ups which you may carry out yourself.

The “

” symbol indicates work to be carried out by your Yamaha dealer.

Item

Actions

Initial

Every

10 hours

(1 month)

50 hours

months)

100

hours (6
months)

200

hours (1

year)

Anode(s) (external)

Inspection / replace-
ment

Anode(s) (internal)

Inspection / replace-
ment

Battery

Inspection / charging

Cooling water pas-
sages

Cleaning

Cowling clamp

Inspection

Fuel filter (can be dis-
assembled)

Inspection / cleaning

Fuel system

Inspection

Gear oil

Change

Greasing points

Greasing

Idling speed (EFI mod-
els)

Inspection / adjustment

PCV (Pressure Con-
trol Valve)

Inspection

Power trim and tilt unit

Inspection

Propeller and cotter pin

Inspection / replace-
ment

Shift link / shift cable

Inspection / adjustment

Thermostat

Inspection

Содержание F115D



















































































Результаты поиска

Содержание F115D

Отзывы:

Похожие инструкции для F115D

Бренды по названию

Популярные бренды

Yamaha F115D, Руководство пользователя

Результаты поиска

Содержание F115D

Отзывы:

Похожие инструкции для F115D

Бренды по названию

Популярные бренды