Yamaha F115D Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 82

background image

Basic components

19

EMU26521

Low oil pressure warning indicator

If oil pressure drops too low, the warning in-
dicator will start to blink. For further informa-
tion, see page 26.

CAUTION:

ECM00020

●

Do not continue to run the engine if the
low oil pressure warning indicator is on
and the engine oil level is lower. Seri-
ous engine damage will occur.

●

The low oil pressure warning indicator
does not indicate the engine oil level.
Use the oil dipstick to check the re-
maining oil quantity. For further infor-

mation, see page 30.

EMU26571

Overheat warning indicator

If the engine temperature rises too high, this

indicator will flash. For further information on
reading the indicator, see page 25.

CAUTION:

ECM00050

Do not continue to run the engine if the
overheat warning indicator is on. Serious

engine damage will occur.

EMU26581

Overheat warning indicator (digital
type)

If the engine temperature rises too high, the
warning indicator will start to blink. For fur-
ther information on reading the indicator, see
page 25.

CAUTION:

ECM00050

Do not continue to run the engine if the
overheat warning indicator is on. Serious

engine damage will occur.

1. Low oil pressure warning indicator

ZMU04754

ZMU01736

1

1. Overheat warning indicator

ZMU04715

ZMU01737

1

«
...
22
23
24
25
26
...
»

Содержание F115D



















































































Отзывы:

Нет отзывов

Похожие инструкции для F115D

Бренд: Gan Systems Страницы: 24

Бренд: Data I/O Страницы: 175

Бренд: MSI Страницы: 92

Бренд: Aeroflex Страницы: 20

Бренд: Advantech Страницы: 3

Бренд: IBASE Technology Страницы: 76

Бренд: Variscite Страницы: 2

Бренд: Merit Страницы: 4

Бренд: Unicorn Computer Страницы: 36

Бренд: Avalue Technology Страницы: 80

Бренд: Texas Instruments Страницы: 24

Бренд: JETWAY Страницы: 57

Бренд: Socket Страницы: 37

Бренд: Supermicro Страницы: 119

Бренд: Tekram Technology Страницы: 42

Бренд: Suzuki Marine Страницы: 63

Бренд: Danfoss Страницы: 2

Бренд: Shenzhen Страницы: 87

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды