Yamaha F115D Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 82

background image

General information

9

dry rags.

●

Do not overfill the fuel tank.

●

Tighten the filler cap securely after re-
fueling.

●

If you should swallow some gasoline,
inhale a lot of gasoline vapor, or get
gasoline in your eyes, get immediate
medical attention.

●

If any gasoline spills onto your skin, im-
mediately wash with soap and water.
Change clothing if gasoline spills on it.

●

Touch the fuel nozzle to the filler open-
ing or funnel to help prevent electro-

static sparks.

CAUTION:

ECM00010

Use only new clean gasoline which has
been stored in clean containers and is not
contaminated with water or foreign mat-

ter.

EMU25570

Gasoline

If knocking or pinging occurs, use a different
brand of gasoline or premium unleaded fuel.

Gasohol

There are two types of gasohol: gasohol con-
taining ethanol and that containing metha-
nol. Gasohol containing ethanol can be used
if ethanol content does not exceed 10% and
the fuel meets minimum octane ratings.
Yamaha does not recommended gasohol
containing methanol because it can cause
fuel system damage or engine performance
problems.

EMU25680

Engine oil

CAUTION:

ECM01050

All 4-stroke engines are shipped from the

factory without engine oil.

EMU25700

Battery requirement

CAUTION:

ECM01060

Do not use a battery that does not meet
the specified capacity. If a battery which
does not meet specifications is used, the

Recommended gasoline:

Regular unleaded gasoline with a min-
imum octane rating of 86 (Pump Oc-
tane Number) = (R+M)/2

Recommended engine oil:

4-stroke motor oil with a combination
of corresponding SAE and API as
shown in the chart

Engine oil quantity (excluding oil filter):

4.3 L (4.55 US qt) (3.78 Imp.qt)

ZMU01710

«
...
12
13
14
15
16
...
»

Содержание F115D



















































































Отзывы:

Нет отзывов

Похожие инструкции для F115D

Бренд: Garelick Страницы: 3

Бренд: Texas Instruments Страницы: 8

Бренд: JETWAY Страницы: 2

Fatal1ty 990FX Professional

Бренд: ASROCK Страницы: 287

Бренд: Nuvoton Страницы: 5

Бренд: NXP Semiconductors Страницы: 12

Бренд: QDI Страницы: 20

Fatal1ty Z87 Killer Series

Бренд: ASROCK Страницы: 102

Бренд: Biostar Страницы: 51

Бренд: Avalue Technology Страницы: 82

Бренд: Advantech Страницы: 4

Бренд: Gigabyte Страницы: 96

SIDE POWER SRH 240 TC

Бренд: SLEIPNER MOTOR AS Страницы: 28

Бренд: ECS Страницы: 60

Бренд: Texas Instruments Страницы: 19

Бренд: Acer Страницы: 27

Бренд: Acer Страницы: 20

Бренд: Acer Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды