Yamaha F115D Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 82

background image

Maintenance

61

when installing the battery and discon-
nect the black battery cable first when
removing it. Otherwise, the electrical
parts can be damaged.

●

The electrical contacts of the battery
and cables must be clean and properly
connected, or the battery will not start

the engine.

Connect the red battery cable to the POSI-
TIVE (+) terminal first. Then connect the
black battery cable to the NEGATIVE (-) ter-
minal.

EMU29370

Disconnecting the battery

Disconnect the BLACK cable from the NEG-
ATIVE (-) terminal first. Then disconnect the
RED cable from the POSITIVE (+) terminal.

EMU29390

Checking top cowling

Check the fitting of the top cowling by push-
ing it with both hands. If it is loose have it re-
paired by your Yamaha dealer.

EMU29400

Coating the boat bottom

A clean hull improves boat performance. The
boat bottom should be kept as clean of ma-
rine growth as possible. If necessary, the
boat bottom can be coated with an anti-foul-
ing paint approved for your area to inhibit
marine growth.
Do not use anti-fouling paint which includes
copper or graphite. These paints can cause
more rapid engine corrosion.

1. Red cable
2. Black cable
3. Battery

ZMU04246

«
...
64
65
66
67
68
...
»

Содержание F115D



















































































Отзывы:

Нет отзывов

Похожие инструкции для F115D

Бренд: Intel Страницы: 78

Бренд: DFI Страницы: 39

Бренд: Abit Страницы: 104

Бренд: AOpen Страницы: 156

Бренд: Elitegroup Computer Systems Страницы: 82

XRP7664-65-74-75

Бренд: Exar Страницы: 8

Бренд: J&W Страницы: 28

Бренд: Gigabyte Страницы: 40

Бренд: J&W Страницы: 40

Бренд: Intel Страницы: 110

Бренд: JETWAY Страницы: 37

ECM-5716 Series

Бренд: Aaeon Страницы: 131

Бренд: National Semiconductor Страницы: 22

STEVAL-LLL002V1

Бренд: STMicroelectronics Страницы: 29

K10N750SLI-WIFI

Бренд: ASROCK Страницы: 264

Бренд: Norco Страницы: 60

nForce 680i LT SLI

Бренд: XFX Страницы: 137

Бренд: Gigabyte Страницы: 147

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды