Yamaha F115D Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 82

background image

Operation

39

4.

Push the tilt support knob into the clamp
bracket or pull the tilt support lever to-
ward you to support the engine.

WARNING

EWM00260

After tilting the outboard motor, be sure
to support it with the tilt support knob or
tilt support lever. Otherwise the outboard
motor could fall back down suddenly if oil
in the power trim and tilt unit loses pres-

sure.

5.

Models equipped with trim rods: Once
the outboard motor is supported with the
tilt support lever, press the power trim
and tilt switch “

” (down) to retract the

trim rods.

CAUTION:

ECM00250

Be sure to retract the trim rods complete-
ly during mooring. This protects the rods
from marine growth and corrosion which
could damage the power trim and tilt

mechanism.

EMU28052

Procedure for tilting down

Power trim and tilt models / power tilt models
1.

Push the power tilt / power trim and tilt
switch “

” (up) until the outboard motor

is supported by the tilt rod and the tilt
support lever / tilt support knob becomes
free.

2.

Release the tilt support lever or pull out
the tilt support knob.

ZMU04602

UP

UP

ZMU04232

ZMU03449

ZMU03452

«
...
42
43
44
45
46
...
»

Содержание F115D



















































































Отзывы:

Нет отзывов

Похожие инструкции для F115D

Бренд: Lantronix Страницы: 10

Бренд: MSI Страницы: 61

Бренд: MACHINIST Страницы: 15

STM32 Nucleo-32

Бренд: ST Страницы: 37

Бренд: Intel Страницы: 110

Бренд: Xilinx Страницы: 56

Бренд: Unicorn Computer Страницы: 36

Бренд: Global American Страницы: 37

Бренд: Gigabyte Страницы: 93

Бренд: Texas Instruments Страницы: 11

NuMaker NUC980 IIoT

Бренд: Nuvoton Страницы: 46

AR6MXCS- Series

Бренд: BCM Страницы: 9

Бренд: NXP Semiconductors Страницы: 138

Бренд: Maxim Страницы: 33

Бренд: Asus Страницы: 64

Бренд: Asus Страницы: 144

Бренд: Asus Страницы: 96

Бренд: Asus Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды