Yamaha F115D Скачать руководство пользователя страница 39

Страница: 39 / 82

Operation

EMU27740

Shifting

WARNING

EWM00180

Before shifting, make sure there are no
swimmers or obstacles in the water near

you.

CAUTION:

ECM00220

To change the boat direction or shifting
position from forward to reverse or vice-
versa, first close the throttle so that the

engine idles (or runs at low speeds).

EMU27763

Forward (tiller handle and remote
control models)

Tiller control models
1.

Place the throttle grip in the fully closed
position.

Move the gear shift lever quickly and
firmly from neutral to forward.

Remote control models
1.

Pull up the neutral interlock trigger (if
equipped) and move the remote control
lever quickly and firmly from neutral to
forward.

EMU27784

Reverse (automatic reverse lock and
power trim and tilt models)

WARNING

EWM00190

When operating in reverse, go slowly. Do
not open the throttle more than half. Oth-
erwise the boat could become unstable,
which could result in loss of control and

an accident.

Tiller control models
1.

Place the throttle grip in the fully closed
position.

Move the gear shift lever quickly and
firmly from neutral to reverse.

Remote control models
1.

Pull up the neutral interlock trigger (if
equipped) and move the remote control
lever quickly and firmly from neutral to
reverse.

ZMU04229

ZMU04597

Содержание F115D



















































































Результаты поиска

Содержание F115D

Отзывы:

Похожие инструкции для F115D

Бренды по названию

Популярные бренды

Yamaha F115D, Руководство пользователя

Результаты поиска

Содержание F115D

Отзывы:

Похожие инструкции для F115D

Бренды по названию

Популярные бренды