Yamaha F-20B Скачать руководство пользователя страница 79

Страница: 79 / 94

Maintenance

TIP:



If a magnetic gear oil drain screw is
equipped, remove all metal particles from
the screw before installing it.



Always use new gaskets. Do not reuse the
removed gaskets.

4. Remove the oil level plug and gasket to

allow the oil to drain completely.

NOTICE:

Check the used gear oil after

it has been drained. If the gear oil is
milky or contains water or a large
amount of metal particles, the gear
case may be damaged. Have a
Yamaha dealer check and repair the
outboard motor.

[ECM00714]

TIP:

For disposal of used oil, consult your
Yamaha dealer.
5. Put the outboard motor in a vertical posi-

tion. Using a flexible or pressurized fill-
ing device, inject the gear oil into the
gear oil drain screw hole.

6. Put a new gasket on the oil level plug.

When the oil begins to flow out of the oil
level plug hole, insert and tighten the oil
level plug.

7. Put a new gasket on the gear oil drain

screw. Insert and tighten the gear oil
drain screw.

EMU29304

Cleaning fuel tank

WARNING

EWM00921

Gasoline is highly flammable, and its va-
pors are flammable and explosive.



If you have any question about properly
doing this procedure, consult your
Yamaha dealer.



Keep away from sparks, cigarettes,
flames, or other sources of ignition
when cleaning the fuel tank.



Remove the fuel tank from the boat be-
fore cleaning it. Work only outdoors in
an area with good ventilation.



Wipe up any spilled fuel immediately.



Reassemble the fuel tank carefully. Im-
proper assembly can result in a fuel
leak, which could result in a fire or ex-
plosion hazard.



Dispose of old gasoline according to lo-
cal regulations.

1. Empty the fuel tank into an approved

container.

2. Pour a small amount of suitable solvent

into the tank. Install the cap and shake
the tank. Drain the solvent completely.

3. Remove the screws holding the fuel joint

Recommended gear oil:

YAMALUBE outboard gear oil or Hyp-

oid gear oil

Recommended gear oil grade:

SAE 90 API GL-4

Gear oil quantity:

0.250 L (0.264 US qt, 0.220 Imp.qt)

ZMU02065

Tightening torque:

9 Nm (0.92 kgf-m, 6.6 ft-lb)

Tightening torque:

9 Nm (0.92 kgf-m, 6.6 ft-lb)

6AG-9-79-1E0.book 72 ページ２０１４年１１月１０日　月曜日　午後４時８分

Содержание F-20B































































































Результаты поиска

Содержание F-20B

Отзывы:

Бренды по названию

Популярные бренды

Yamaha F-20B, Руководство пользователя

Результаты поиска

Содержание F-20B

Отзывы:

Бренды по названию

Популярные бренды