Yamaha F-20B Скачать руководство пользователя | Manualshive

Страница: 74 / 94

background image

Maintenance

67

fully in neutral until it is running smooth-
ly.

2. Once the engine has warmed up, verify

whether the idle speed is set to specifi-
cation. For idle speed specifications, see
page 9. If you have difficulty verifying the
idle speed, or the idle speed requires ad-
justment, consult a Yamaha dealer or
other qualified mechanic.

EMU38807

Changing engine oil

WARNING

EWM00761



Avoid draining the engine oil immedi-
ately after stopping the engine. The oil
is hot and should be handled with care
to avoid burns.



Be sure the outboard motor is securely
fastened to the transom or a stable
stand.

NOTICE

ECM01711

Change the engine oil after the first 20
hours of operation or 3 months, and ev-
ery 100 hours or at 1-year intervals there-
after. Otherwise the engine will wear
quickly.

To prevent spilling oil where it could cause
damage to nature, it is strongly recommend-
ed that you use an oil changer to change the
engine oil. If an oil changer is not available,
drain the engine oil by removing the drain
screw. If you are not familiar with the proce-
dure for changing the engine oil, consult your
Yamaha dealer.
1. Put the outboard motor in an upright po-

sition (not tilted).

NOTICE:

If the out-

board motor is not level, the oil level
indicated on the oil dipstick may not
be accurate.

[ECM01862]

2. Start the engine. Warm it up and keep

the idle speed for 5-10 minutes.

3. Stop the engine and leave it for 5-10

minutes.

4. Remove the top cowling.
5. Remove the oil filler cap. Pull out the dip-

stick and use the oil changer to extract
the oil completely.

TIP:

When using an oil changer, skip steps 6 and
7.
6. Prepare a suitable container that holds a

larger amount than the engine oil capac-
ity. Remove the drain screw and gasket
while holding the container under the
drain hole. Let the oil drain completely.
Wipe up any spilled oil immediately.

1. Oil changer

ZMU05554

1

ZMU06617

6AG-9-79-1E0.book 67 ページ２０１４年１１月１０日　月曜日　午後４時８分

«
...
72
73
74
75
76
...
»

Содержание F-20B































































































Отзывы:

Нет отзывов

Похожие инструкции для F-20B

Бренд: NAD Страницы: 36

Бренд: NAD Страницы: 3

Бренд: Halcro Страницы: 2

Бренд: Harley Benton Страницы: 2

Бренд: Harley Benton Страницы: 28

Бренд: QUAD Страницы: 4

Бренд: QSC Страницы: 142

Бренд: Jedia Страницы: 16

L-RF-EDFA-14dBm

Бренд: Questtel Страницы: 16

Series VII Aphrodite

Бренд: Hifonics Страницы: 58

Бренд: Kustom Страницы: 7

Grand Integra M-510

Бренд: Onkyo Страницы: 31

D750 The Little Brick

Бренд: Prolude Amplification Страницы: 11

99 Stereo Power Amplifier

Бренд: QUAD Страницы: 18

Бренд: B2 Страницы: 10

Бренд: E&I Страницы: 13

Бренд: E&I Страницы: 12

Бренд: AMC Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды